Assessments - , GPA:
(
)
)
Fabricante : Casio
Arquivo Tamanho: 1.19 mb
Arquivo Nome : qw2758.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
•Remember that reception of the calibration signal depends on the time kept in the digital display. The receive operation will be performed whenever the display shows any one of the calibration times, regardless of whether or not the displayed time is actually the correct time. •When two, three, four, or five receptions are successful, the watch uses the data of the last reception for calibration. When only one reception is successful, the watch uses the data of the successful reception. Receiving indicator Weak Strong l l l llll l l l l llll l l (Level 1) (Level 4) About the Receiving Indicator The receiving indicator shows the strength of the calibration signal being received. For best reception, be sure to keep the watch in a location where signal strength is strongest. •Even in an area where signal strength is strong, it takes about 10 seconds for signal reception to stabilize enough for the receiving indicator to indicate signal strength. •Use the receiving indicator as a guide for checking signal strength and for finding the best location for the watch during signal receive operations. •The Level 4 receiving indicator remains on the display in all modes following reception of the time calibration signal and calibration of the watch’s time setting. The Level 4 receiving indicator is not displayed if signal reception was unsuccessful or after manual adjustment of the current time setting. •The Level 4 receiving indicator is displayed only when the watch is able to successfully receive both time and date data. It does not appear when only time data is received. •The Level 4 receiving indicator indicates that at least one of the calibration signal receive operations was successful. Note, however, that the Level 4 receiving indicator is cleared from the display at 3:00 a.m. each day. To perform manual receive 1. Place the watch on a stable surface so its top (12 o’clock side) is facing towards a window. •Note that signal reception is poor when the 12 o’clock side of the watch is not facing towards a window. 2. In the Timekeeping Mode, hold down D for about two seconds until the watch beeps. l l l llll l l l l llll l l Receiving indicator 3. Release D and the current time flashes to indicate that signal reception has started. •Time calibration signal reception takes from two to five minutes. Take care that you do not perform any button operations or move the watch during this time. •After signal reception is complete, the display of the watch changes to the Last Signal screen. Note •To interrupt a receive operation and return to the Timekeeping Mode, press D. •If the receive operation is unsuccessful, the message ERR appears on the display for about one or two minutes. After that, the watch returns to the Timekeeping Mode. •You can also change from the Last Signal or ERR screen to the normal timekeeping screen by pressing D. To turn auto receive on and off 1. In the Timekeeping Mode, hold down A until the transmitter indicator starts to flash, which indicates the setting screen. 2. Press C three times to move the flashing to the auto receive on/off setting. 3. Press D to toggle auto receive on (ON) and off (OF). •If the current Home City setting is a city code that does not support signal receive, “xx” appears in place of the on/off indicator. This means you cannot turn auto receive on or off. 4. Press A twice to exit the setting screen. On/off status To display the digital time and Last Signal screen •In the Timekeeping Mode, press A to cycle through the digital time screens as shown below. •In the Timekeeping Mode, press D to display the Last Signal screen (indicated by GET). The Last Signal screen shows the date and time of the last successful time calibration signal reception. Press D. Seconds Last Signal Screen Receive date Receive time Alternate at two- second interval Day of week Hour : Minutes Seconds Month—Day A A Press A. Month—Day Signal Receive Troubleshooting Check the following points whenever you experience problems with calibration signal reception. Problem Cannot perform manual receive. Auto receive is turned on, but the Level 4 receiving indicator does not appear on the display. Time setting is incorrect following signal reception. Probable Cause •The watch is not in the Timekeeping Mode. •Your current Home City is not one of the following city codes: BER, PAR, or LON. •The transmitter setting is incorrect. •The transmitter setting is incorrect. •You changed the time setting manually. •The watch was not in the Timekeeping or World Time Mode, or you performed some button operation during the auto receive operation. •Even if receive is successful, the Level 4 receiving indicator disappears every day at 3 am. •Time data (hour, minutes, seconds) only was received during the last receive operation. The Level 4 receiving indicator appears only when time data and date data (year, month, day) are both received. •If the time is one hour off, the DST setting may be incorrect. •The Home City code...