Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
When you see the circuits you want, press and hold [#]. Those circuits will turn on their relays, as shown by the green panel lights. When you release the [#], the circuits will turn off their relays. You can now choose and test other circuits or press [*] to quit Note: Only circuits setup as Bell Zones will appear. If you have an LTR8-512 with a single clock system attached, you will only see circuits 1-6. If you have an LTR4-512 with a single clock system attached, you will only see circuits 1-2 [*] Return to time and date display 14 LTRx-512 Installer’s Guide Auto Test the Bells Use the Auto Bell Test feature to turn on all bell relays once per minute at the start of each minute. Once you start this function, you can test the continuity of your bell wiring circuits. Use the “hidden code” 2355878 [BELLTST] to start the Auto Bell Test. When you enter this code, ignore anything that displays on the screen Use Function [6] to disable any relays that you do not want to use in your testing Once you finish testing, make sure you enter the hidden code again to stop the Auto Bell Test and use Function [6] to enable any relays that you earlier disabled Set Daylight Savings • Your Master comes set to adjust for daylight savings in the United States. If you live outside the United States or if your region does not observe daylight savings, use Function [7] to change the country code Press Display [#] SELECT FUNCTION CODE [7] ENTER COUNTRY CODE FOR DAYLIGHT SAVINGS TIME ADJUSTMENT: 08 [0]..[9] Enter your country code from Appendix C [#] Press [#] to accept (or [*] to cancel) If your region does not observe daylight savings, then set your country code to 00 Setup Communications (LTR8-512 and LTR8-512M only) • Use Function [B] if you use the LTR MasterLink or Terminal Manager software with your Master. You can setup your LTR8-512 with LTR MasterLink using RS-232 (serial), RS-485 (networked) or Modem (remote) Communications You must enter these same settings for your LTR8-512 in the Terminal Manager or LTR MasterLink software 15 LTRx-512 Installer’s Guide You cannot choose function [B] directly. To enter Communications, press [#][9][0][0][#] Press Display [#] SELECT FUNCTION CODE [9] Press [9], then [0][0] Press [0] twice to see [B]=COMMUNICATIONS [#] COMMUNICATIONS SETUP SELECT BAUD RATE: [2]400 -OR-[9]600 [2] or [9] Enter [2] for 2400 baud or [9] for 9600 baud (9600 is the default) 9600 (or 2400) BAUD SELECTED ENTER TERM ID# 000 Note: If the LTR8-512M will be programmed to call the NIST Atomic clock, you must select 9600 Baud. [0]..[9] Enter a unique Terminal ID # from 001-127 (065 is the default) [3] PRESS [#] TO CONFIRM [#] Press [#] to accept -or[*] Press [*] to cancel and try again Congratulations! You have finished the basic setup of your LTRx-512 Master. All of the Master functions are described in the next section of this guide, such as setting up your bell schedules. For detailed information, please refer to the User’s Guide. The Master will exit itself out of Program Mode once you stop using the keypad for 5 minutes or if you wish to exit programming mode immediately to prevent others from accessing the Master Clock, simply enter an invalid password. (For example) [#] SELECT FUNCTION CODE [0] [0]=ENTER PASSWORD [#] 99 [#] PASSWORD: 99 16 LTRx-512 Installer’s Guide Functions Defined [#] Starts the Programming Functions and Confirms Entries [*] Ends Program functions and/or Cancels Entries (except the “Quick Check”) Quick Check Commands Quick Check commands display system information for about 2 seconds. You can press any of the three quick check keys ([*], [1] or [3]) when the Master is in Clock Mode. Quick Check Command [*] Status Any time you see the time and date, you can press [*] to see the Master status. You will see the firmware version, terminal ID#, communications baud rate, time display format (12-hr or 24-hr), daylight savings country code and the clock types you have chosen Quick Check Command [1] Edit Keys Any time you see the time and date, you can press [1] to see the edit key descriptions. You can use the edit keys to program Bell Schedules, Automatic Schedule Change Dates, and Holiday Dates. When you press [1], you will see [1] EDIT [9] 1ST [3] PRV [#] NXT [4] DEL [*] EXIT [6] ADD Quick Check Command [3] 12/24 Hour Display Any time you see the time and date, you can press [3] after entering your password to toggle the time and date between 12-hour and 24-hour format. The 12-hour format shows AM or PM, while the 24-hour format shows the day of the week (or ‘HO’ for Holiday). Program Keys To access the Master’s programming functions, press the [#] key. As described below, some functions require a user password, and advanced functions require the administrator password. [0] = Password You must enter a password for most programming functions. To enter your password, press [#][0][#] Enter your 6-digit password, then press [#] 17 LTRx-512 Installer’s Guide Once you enter your password, you can now p...