Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
2 Materials included in this package: 1. SDB Signal Distribution Box (1pc) 2. CS Control Station (2pcs) 3. CSDIN Control Station DIN Cable (2pcs) 4. CSSC Control Station Source Cable + DC Power Pigtail (2pcs) 5. SDBSC Signal Distribution Box Source Cable (2pcs) 6. SDBPC Signal Distribution Box Power Cable (1pc) 7. SDBHP Signal Distribution Box Hardware Package (1pc) (Screws/Washers) Optional Enhancements (Not included, must be purchased separately) MCS Master Control Station (1pc) (See page 10) GCS Game Control Station (1pc) (See page 10) 3 SDB45 System Overview The SDB45 is a versatile audio/video switching system and has the capacity for four Audio/Video inputs and five Audio/ Video outputs along with a separate audio output for connecting an FM modulator to the vehicle radio. The SDB45 consists of a Signal Distribution Box (SDB) and two Control Stations (CS) along with cabling for two signal sources (SDBSC) and cabling (CSSC) for connecting two video screens. Additional control stations (CS), Signal Distribution Box Source Cables (SDBSC), a Master Control Station (MCS) and a Game Control Station (GCS) can be purchased to further enhance the system. Each CS is comprised of a control station, a trim ring, a DIN cable for connecting the control station to the SDB, a control station source cable (CSSC) for connecting the output of the SDB to a video screen. Each control station has a volume control and two headphone jacks for listening to the selected source. In addition, each control station has an IR sensor that allows each user to control the source component that is selected on the control station. The Optional MCS is comprised of a master control station, a DIN cable for connecting the master control station to the SDB, a control station source cable for connecting the audio output of the SDB to an FM modulator (which is included) and a trim ring. The MCS can switch the audio from any of the four A/V sources to the FM modulator (or to the low-level input of a receiver) so that the audio can be played through the vehicle radio. The MCS also has the capability of setting a 10-minute delay. When the delay is enabled, the system will remain on for 10 minutes after the vehicle is turned off. The MCS also has an IR sensor for controlling the source components. (NOTE: The MCS is NOT required for the system described above.) The optional GCS is comprised of a game control station that has RCA jacks on the front and back, a 15-foot RCA to RCA cable and a trim ring. The GCS can be used as a game port for easy access when connecting a video game, camcorder, portable DVD or other A/V input device. The SDB45 can be used with essentially any source component and any video screen available. (NOTE: The IR repeater in this system may not work with non-Audiovox components.) 4 GENERAL INSTALLATION APPROACH: 1. Decide upon system configuration and options that will be installed (i.e.: what components, VCP, DVD, TV Tuner, Video Game, Monitors, etc.). 2. Review all manuals to become familiar with electrical requirements and hook ups. 3. Decide upon mounting locations of all components and method of mounting. 4. Prep the vehicle by removing any interior trim necessary to gain access to vehicle’s wiring as well as all areas where interconnecting wire harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim components etc.), this should be done now as well. 5. Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagram Sheet attached as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 6. Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 7. Connect all components together (electrically) and verify proper operation of all system functions. Note: This is best done BEFORE components have been permanently mounted. 8. After verifying proper operation of the system, 5 proceed to mount each component. 9. When all components are mounted recheck the entire system to be sure it is functioning correctly and ensure that no wiring was pinched or connected improperly during final installation. Use the supplied cable clamps on the control station interconnect. VEHICLE PREPARATION 1. Locate a constant power source (+12 Vdc at all times) and an accessory power source (+12Vdc present when the ignition key is in the accessory and run positions. 0Vdc should be present when the ignition key is in the OFF position). Generally, these wires can be found at the ignition switch or fusebox. (NOTE: Ensure that the constant and accessary power are fused at their sources. Failure to do so may resul...