Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
TAPE 8 To play back the recording from a cassette deck attached to the TAPE 1 input, press TAPE. ‘TAPE 1’ is shown on the display. Selecting this input overrides the other source selectors. It is also possible to monitor a recording while it is being made, provided your cassette deck is a 3-head type. To do this, press TAPE. Switching this button in/out allows an A/B comparison between the source signal and the recorded signal. 8 Setting up your A32 integrated amplifier Setting up your A32 integrated amplifier Choose setting Adjust BALANCE Adjust BASS Adjust TREBLE Adjust LEFT RIGHT –dB +dB –dB +dB Customize -> DOWN UP edit STANDARD FINE REFERENCE continue Volume Resolution GRAPHIC/ NUMERIC edit GLOBAL/ PER SOURCE continue edit ARCAM Amp continue edit AUX/ PHONO continue edit NO/YES RESTORE SETTINGSPHONO/AUX TEXT WELCOME MESSAGE TONE CONTROL edit continue edit continue TRIM VOLUME DISPLAY INPUT TRIMS Welcome Message Phono/Aux Text Restore Settings Volume Resolution Volume Display Input Trims Tone Control ‘Switch on’ state ‘Switch on’ state VOLUME INTRODUCTION The A32 allows you to adjust listening settings to suit your taste, and to customize various features of the amplifier to fit your system. Use this diagram to help you navigate through the settings available. The ENTER and SELECT buttons are represented in the diagram by the symbols and respectively. The Control knob is shown as . ADJUSTING LISTENING SETTINGS The default display mode is VOLUME, where the control knob is used to adjust sound level. Press SELECT to enter edit mode and cycle through the other sound settings: BALANCE, BASS and TREBLE. When a setting is selected, adjust it with the control knob. Press ENTER to fix the change you have made and return to default (volume) mode, or press SELECT again to move to the next setting. CUSTOMISING AMPLIFIER SETTINGS Press SELECT until the display shows ‘CUSTOMIZE->’. Now rotate the Control knob to choose which setting you wish to alter. Press SELECT to adjust the chosen setting with the Control knob. Press ENTER to confirm the adjustment or press SELECT to confirm the adjustment and move on to the next item. Press ENTER twice to leave the Customize menu. Volume Resolution – Standard, fine or Reference. ‘Standard’ and ‘Fine’ represent different levels of volume control sensitivity.The ‘Reference’ setting gives absolute increments in 0.5dB steps. Volume display mode – graphic or numeric shows the volume either as a bar graph or as a number. If Volume resolution is set to ‘Reference’ a numeric volume display shows the actual decibel figure. Input Trims – use the source select buttons and Control knob to set input trims for each source. Input trims are used to compensate for variations in output levels of different source equipment. Tone Control – Global or Per source. This specifies the scope of changes for ‘Bass’ and ‘Treble’ tone settings. The default setting is ‘Global’ which affects all inputs equally. ‘Per source’ allows you to set tone controls for individual inputs: once set, the amplifier remembers tone settings for each input. Welcome message –You can change the power on Welcome message from ‘Arcam Amp’ to display your name, postcode, etc. When customising the message, use the UP and DOWN buttons to select the cursor position and the Control knob to change the letter. Phono/Aux Text – If you have had the optional Phono module added, choose ‘Phono’ so this word is displayed when the input is selected. The default is ‘Aux’. Restore Settings – this restores all amplifier settings, including Input trims and the Welcome message, to their factory defaults. 9 10 Using the remote control NOTE Remember to install the two AAA batteries supplied before trying to use your remote control. Do not place anything in front of the FMJ badge on the top left of the CD player (where the IR receiver is located), or the remote control may not work. CR-389 REMOTE CONTROL The CR-389 remote control gives access to all functions available on the front panel of the A32. It also has controls to operate Arcam CD players, AM/FM tuners and DAB tuners. The remote control transmits Philips RC-5 type codes. FM DAB PROG DISP RPT MODE BAND 1-9 2-10 3-11 FM DAB SEL TUNER CR-389 CD AMPLIFIER AV DVD VCR TAPE PHONO AUX CD TUNER ENTER SP1 SP2 DISP MENU DISP 4-12 5-13 6-14 7-15 8-16 TUNER These buttons are used to control tuner functions. Note that the FM/DAB lights indicate into which mode you are switching the remote control. The lights only illuminate for five seconds to conserve battery power. If neither light is illuminated this does not mean that the remote control is not working! (UP and DOWN) Perform the same function as the buttons on the front panel (see page 6). SELECT Performs same function as the SELECT button on the front panel. It allows you to use the remote’s volume switch in the same way you use the control dial on the front panel – to adjust various amplifier settings (see page 8). Note that pressing + corresponds to t...
Este manual também é adequado para os modelos :receptor e amplificador - Handbook A32 (338.17 kb)