Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Major speaker manufacturers have been using Speakon connectors on their products for years, so chances are you are ready to use the Speakon connection. With Speakon connectors, you can connect straight from the amplifier to the speaker. The Speakon connector used on this amplifier meets all known safety regulations. Once wired correctly, the connector cannot be plugged in backwards, causing the type of inverted polarity situations that have become common with banana hookups. This connection will provide a safe, secure and reliable method of connecting your speakers to your new amplifier. You can purchase the Speakon® NL4FC connectors from your local audio dealer. ©American Audio® --V4000plus™ Power Amplifier User Manual Page 8 Diagram 10 Typical speaker output using bare wire. Insert bare wire into the binding post and tighten. Diagram 11 OPERATING MODES: Always configure your amplifier operating mode before beginning operation. If you want to change it durAlways configure your amplifier operating mode before beginning operation. If you want to change it during performance. You must decrease the gain controls to their lowest levels to protect the speakers from any popping noise. Stereo Operation -Page 10/Figure 9 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (full counter-clockwise). Turn your amp on. Turn your input source level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. Mono Bridge Operation -Page 9/Figure 8 details a mono bridge set-up. Be sure your amplifier and all other audio equipment is powered down. Flip the Stereo/Mono Bridge switch to the Mono Bridge position. Connect an input signal to channel one. Connect your speaker across the red output binding post on the rear of your amplifier. Turn your equipment on (your amplifier should always be the last item you turn on). Apply an input source signal to your amplifier. Turn channel two gain up. Use the channel one gain to regulate your amplifier output. Bridged-Mono Mode Caution -The TheThe voltage voltagevoltage acr acracross ossoss the thethe output outputoutput terminals terminalsterminals of ofof a aa bridged bridgedbridged V4000 V4000V4000V4000plus™ amplifier may equal or exceed 100 volts RMS and may be as high as 130 volts. Use fully insulated CLASS ONE wiring, and the load must be rated for up to 2500 watts (@4 ohms) Parallel Mono -“Parallel ” ties the two channel line inputs together so that they will both be driven by the same signal, without the need for external jumpers or wiring. Both amplifier channels will operate independently. Though they carry the same signal, their gain controls affect only their respective channels, and they both must use their respected speaker outputs. Never attempt to parallel the speaker outputs, this may cause serious damage to your amplifier! This mode is recommended when using the V4000 V4000V4000V4000plus™ to run bass speakers, to achieve better low end. To run in parallel mono mode connect your system as you would if you were going to run in stereo mode. Then flip the mode switch to “MONO.” Be sure the amp is off or the power is disconnected before making any changes. Subwoofer Mode -This mode sends low frequencies to your speakers without the use of an external cross-over. The subwoofer operation can be operated in stereo, mono, or bridge mono modes. Change the different operating modes by flipping the mode switch on the rear of the unit to your desired operating mode. Also, set the subwoofer mode switch to the subwoofer position. Use the frequency selector to adjust the subwoofer output frequency from 20Hz to 200Hz. The different subwoofer modes are listed as follows; Bridge Subwoofer -This operation allows you to get the most possible power out of your amplifier for the sole purpose of running a high powered subwoofer loudspeaker in mono. To avoid amplifier overheating, never run the amplifier below 4 ohms in this mode. In this mode you may use the frequency adjustment on the rear of the amp, to control the frequency output level. Frequencies may be adjusted from 20Hz to 200Hz. Figure 14 details a typical Bridge Subwoofer set up. Stereo Subwoofer -This operation is similar to the Bridge Subwoofer operation but in stereo. This operation allows you to run several subwoofers down to a minimum of 2 ohms. To avoid amplifier overheating, never run the amplifier below 2 ohms in this mode. Set up this mode as you would a standard stereo set up. Be sure both channels are set to “SUBWOOF.” In this mode you may use the frequency adjustment on the rear of the amp, to control the bass frequency output level. Frequencies may be adjusted from 20Hz to 200Hz. Figure 15 details...