Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Use the mounting diagram for mounting the vibe Xe3 Crossover/Equalizer. Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenfer if there is a sudden stop, like an emergency stop. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from the hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. -3- WIRING CONNECTION SUB REAR OUT OUT FRONT OUT B+ (Red) GROUND (Black) REMOTE (Orange) 0000 00 I 00 L R L R > SUBWOOFER REAR SPEAKER ИЗ <\R N id —c( DNT N id FRONT SPEAKER The vibe XE3 come with a three pin modular wiring harnass. This wiring harnass contains color coded wires. The red wire is the +12V, the black wire is the ground and the orange wire is the remote turn-on lead. Connecting these wires should be fairly easy. Use the following guidelines to assist you in your connections. 1. Pull your source unit out of the dash far enough until the wires are exposed 2. Use a test light or a (digital) volt meter and find a constant +12V lead for the radio. Splice into this lead. Take the red wire from the wiring harnass and connect it inline with the +12V wire using a barrel connector of appropiate size. Crimp the wires back together. 3. Locate the ground wire supplied to the source ans splice into it. Take the black wire from the wiring harnass and connect it inline with the ground wire using a barrelconnector of apropiate size. Crimp the wires back together. If your ground wire screwed to the back of your source, you may use this to ground the black wire. Be sure to use a ringterminal of the appropiate size and tighten the screw securely. If your source is receiving its ground through the antenna, you will need to find your own grounding point. Locate a metal area close to the vibe XE3 that is a good source of ground (preferably the floor). Eliminate unwanted paint using a wire brush or sandpaper. Terminate the black wire using the correct size of ring terminal and attach it to the bare metal. Spread silicone over the screw and bare metal to prevent rust. 4. You should now have one wire left, the remote turn-on. This wire is to be connected up to the remote turn-on lead coming out of the source unit. Use a barrelconnector of appropiate size to interlink these wires. If your source does not have a remote turn-on lead, you will need to find a switched +12V supply. This can be done by using a toggle switch or using an ignition controlled lead. 5. Plug the modular three pin harnass into the corresponding socket on the rear of the vibe Xe3. SIGNAL CABLES Choose the correct length and style of RCA patch cables for your needs. Better RCA's, such as the ones from the Caliber Get Connected series, have gold-plated connectors and multiple layers of shielding for better noise rejection (consult your official LANZAR dealer about these cables and RCA's). -4- OPERATION FRONT PANEL 1. Power on/of indicator. This LED will illuminate when the system is in operation. 2. Peak or clipping indicator. This LED will illuminate when your VIBE-XE3 is over loaded or when the signal is clipping. 3. Master volume control. Used to control the system volume when the source unit is preset to a specific volume. 4. Fader. Adjusts the proportionate level of the front- and rear outputs. 5. Sub-woofer level control. Adjusts the sub-woofer output level below the crossover frequency selected. 6. 50Hz. Adjusts the cut of or boost up to 18dB at 50Hz. 7. 250Hz. Adjusts the cut of or boost up to 18dB at 250Hz. 8. 1 KHz. Adjusts the cut of or boost up to 18dB at 1000Hz. 9. 2.5KHz. Adjusts the cutof or boost up to 18dB at 2500Hz. 10. 6.5KHz. Adjusts the cut of or boost up to 18dB to the 6500Hz shelving equalizer. OPERATION TOP PANELAND CONNECTIONS A. Input. Docking ports for the RCA connectors arriving from the source unit:s output. B. Input level control. Input sensitivity level control adjusts to your source unit:s output. C. Front output. Docking ports for the RCA connectors leading to the front speaker amplifier. D. Rear output. Docking ports for the RCA connectors leading to the rear speaker amplifier. E. Subwoofer output. Docking ports for the RCA connectors leading to the subwoofer amplifier. F. 3-pin modular socket.(at the back) Contains the power, ground and remote turn-on input. CROSSOVERS G. Sub-woofer crossovers. This four position switch allo...