Assessments - 4, GPA: 3.5 ( )

Fabricante : ARC Audio Arquivo Tamanho: 1021.8 kb Arquivo Nome : Língua de Ensino:

Meaning it has more than one channel of speaker outputs. It is equipped with a large block style terminal for speaker connection. Make this connection carefully and neatly. Strip your wire back and twist the exposed leads and insert into the block terminal while being careful that there is no loose or frayed strands of wire and tighten the Phillips head screw down on the terminal till the wire is tightly secured in place. If the wires ever come in contact with each other the amplifier will go into protection. Know your total ohm load before you make any connections. Installation Instructions 1. Disconnect the negative cable from the car battery. Tape up the end so it is isolated form the battery. 2. Run an 8 AWG power wire (4 AWG min.for FD4150 or if you are using multiple amplifiers) from the battery to the amplifier. Plan this part of the installation carefully.This cable will carry very high current. If it should short to the body and it is not properly fused it could catch fire. 3. Connect the power wire to the battery using a fuse capable of the total current load of all amplifiers connected. Don't install the fuse yet. Wait until the end. Locate the fuse as close as possible to the battery. If the fuse is further that 18 inches (wire length) from the battery you should reevaluate the wire and fuse placement. 4. Find the closest clear metal area to the amp for a ground. Sand, grind or scrape all paint and undercoating from the body and screw the ground securely to the body. It is advisable to test the ground with an ohmmeter between the ground cable and the negative battery cable to insure a good low resistance connection. Some alloys used in modem cars do not offer the best ground. If you believe this is the case consult with the vehicle manufacturer. 5. Run the speaker wire to the speakers. It is advised that you leave some extra wire at this point. You can "clean it up"later. 6. If you haven't already done so, mount the amp now. 7. Connect the power and ground to the amplifier. Only after this step should you install the fuse at the battery. 8. Connect the remote wire from the head unit to the amplifier. Now is a good time to turn on the amp for the first time. Make sure it turns on properly and does not go into protect. G 9. Connect the speaker wire to the amp and speakers (make sure the amp is off first). Make sure the polarity (+ and-) is correct. 10. Connect the RCA's to the amp. 11. Double check the amplifier controls at this time. Make sure everything is set correctly for your system. 12. Now you're ready to play it for the first time. It is best to leave the gain all the way down at first. Start with the head unit volume low and work your way up. 13. Now you can tune the amp.Take your time and make only one adjustment at a time. It may take some time to get the system fully adjusted. During this time the amp is drawing current from the battery. You should check the battery voltage from time to time and re-charge it if it gets low. Battery voltage can affect the way the amplifier performs. 14. You're done. Now have fun. 7 FD2100 and FD2200 BRIDGED 4 OHMS Set to Set to LOW L+RSUM ) 0 0 0 0 1000000000000 4 OHMS B FD2100 and FD2200 STEREO FULL RANGE OR HIGH PASS 4 OHMS/2 OHMS Set to Set to HIGH or FULL STEREO OPTIONAL SECOND SET 2 OHM STEREO FD4100 and FD4150 STEREO 4 CHANNEL HIGH PASS + 12V OPTIONAL SECOND SET 2 OHM STEREO OPTIONAL SECOND SET 2 OHM STEREO 10 FD4100 and FD1500 STEREO FULL RANGE OR HIGH PASS With MONO SUBWOOFER 11 FD4100 and FD4150 STEREO 4 CHANNEL SET BOTH INPUTSWITCHS TO "BRIDGED" HIGH PASS «CH. 2 CH. 'O' o dBia w/bass FHEQ Hz FREQ Hz 95 __96 RANGE w°n wn USE 4 OHM SPEAKERS ONLY WARNING: THE FD4150 WILL PRODUCE320 WATTS X 2 NOTRESPONSABLE FOR DAMAGED SPEAKERS FD4100 and FD1500 2 CHANNEL BRIDGED SET BOTH IN PUT SWITCHS TO LOW PASS Use the Front inputs, Front gain 13 POWER AND INPUT CONNECTIONS DUAL BATTERY or BATTERY AND CAPACITOR This is a stock ground wire on the battery between the battery and the body. It should be Upgraded to 4 AWG...

Baixe o seu

Para fazer o download, introduza 2 dígitos :