Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
As the input increases above threshold, the output takes the shape of the de-emphasis curve. When both pre and de-emphasis are switched out, the Model 722 works exactly like the Model 720. RCH DENSITY - adjusts RANGE - when switched the Relative Crest Height to the “.10” position it adds ach (RCH) of the output. a 10dB boost in the input The higher the RCH and a 10dB cut in the and of (clockwise) the louder the output. The PEAK CEILING output. The lower the is therefore 10dB lower nnel RCH (counter-clockwise) than the settings shown of the lower the average on COARSE and FINE level in the output. controls. Applications Sound Contracting — protection of amplifiers and speakers from overload; increased loudness; maximized use of available power. Recording — preventing sudden peak overload of mixer or recorder; tightening tracks; special eff e c t s , e t c . Mixing — used as a program limiter, the Dominator ll will keep a track “rock steady” for “layering” into or on top of a mix. Digital Sampling — obtaining good full scale samples free from peak overload, i.e. no more missed samples. Digital Recording — insuring clean recording by stopping clipping of peaks and overshoots. Maximizes bit usage for less distortion. Satellite Uplink — Modulation control to prevent splattering on high frequency audio, gives reduced distortion, better signal-to-noise. Broadcasting — AM and FM modulation control for increased loudness; cleaner sound; use in production for greater consistency of tapes, punchier voice-overs. Location Film Shoots — anti-crash for dialog and sound effects recording. Post Production — Soundtrack peak control; managing difficult dialog; controlling transient sound effects. Optical Recording and Transfer — prevents “valve clash”, gives higher average level with low distortion and better signal-to-noise performance. Analog Disk Mastering — peak control for high allowable average cutting levels; less limiter degradation to the program; brighter, punchier sound. C/D Mastering — peak and density control for more accurate digitizing, cleaner sound requiring less error correction on playback; no limiter induced sound degradation. STL & Phone Line Driver — maximize signal-tonoise without overload distortion. Video and Audio Tape Duplication — “Hotter” transfers without saturation. LIMITING (meter) displays the limiting (from gain reduction and clipping) in the channel with the greatest amount of limiting. he FINE - adjusts the COARSE - switches POWER - switches en PEAK CEILING by the PEAK CEILING AC mains on and off. om ±1dB in 0.2dB steps. in 2dB steps from +2 to +24dB(pk). “Off” position engages bypass relays. Dominator II™ Models 720, 722 NOMINAL OPERATING LEVEL (Peak Ceiling RANGE switch) 0dBu (for use with +4 or +8dBu) -10dBu INPUT Connector: 3-Pin XLR female (pin 1 ground, pin 2 positive, pin 3 negative) Type: Transformerless, servo balanced with passive 4th order RF filter Chassis grounded per AES standards Impedance: 19.5 kW Unterminated; same 600W with rear-panel terminator engaged same (terminator lifts in bypass) Nominal Level: from 0dBu to +8dBu from -10dBu to 0dBu Maximum Level: +26dBu +16dBu (+14.8dBV) CMRR (typical): > 50dB 20Hz to 10kHz same RF Rejection: > 28dB at 800 kHz; > 60dB above 2 mHz same OUTPUT Connector: 3-Pin XLR male (pin 1 ground, pin 2 positive, pin 3 negative) Type: Transformerless, servo balanced, chassis grounded per AES standards Output Impedance: 65W same Nominal Level: from 0dBu to +8dBu from -10dBu to 0dBu Maximum Level: +25dBu PK* +15dBu PK* AUDIO (Controls set for unity gain, no limiting and flat response except as otherwise noted) Frequency Response: +0.2dB 4.5Hz - 50kHz same Dynamic Range: > 108dB > 106dB Hum & Noise (unweighted, 22 Hz - 22 kHz): < -82dBu < -90dBu Crosstalk: < -60dB up to 10kHz same THD (Ref.: 1kHz, no limiting): < 0.006% (+12dBu in) < 0.006% (+2dBu in) SMPTE IMD: < 0.006% (+12dBu in) < 0.006% (+2dBu in) 720/722 CONTROL & METERING PARAMETERS (on front panel unless otherwise noted) INPUT GAIN: +14/-21 dB typical same PROCESS ON/OFF: ON: Active / OFF: Hardwire Bypass same LF EQ Boost/Cut: ± 5 dB same HF EQ Boost/Cut: ± 5 dB same XOVER 1 Frequency: 100 Hz / 210 Hz same XOVER 2 Frequency: 1.7 kHz / 3.4 kHz same RELEASE Time: 150 mSec to 7 Sec same RCH (Relative Crest Height) DENSITY: -5 to +5 same STEREO COUPLING: ON / OFF same PEAK CEILING: +1 to +25dBu (PK)** -9 to +15dBu (PK)** Peak Ceiling is adjusted with the COARSE (2dB steps), FINE (0.2dB steps) and RANGE (0dB/-10dB) controls LIMITING Meter: 10 segment meter indicates up to 15dB of gain reduction in the channel with the greatest amount of limiting 600 OHM INPUT TERMINATION: Each channel is switchable on rear panel (lifts in bypass) REMOTE Control Jack: A four pin RJ11 telephone-style connector on the rear panel provides remote control capacity of the PROCESS ON/OFF bypass relays and dry “tally” contact for a remote status indicator 722 CONTROL PARAMETERS (722 only) EMPHASIZED LIMITING (switches are ...
Este manual também é adequado para os modelos :receptor e amplificador - Dominator II 720 (59.1 kb)