Assessments - 3, GPA: 3.7
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Refer to the operating instructions of the TV on this operation. continued 95GB Additional Information The TV’s remote cannot be used to control the connected component when using the Control for HDMI function. • Change the input of the receiver to the HDMI input connected to the component. Sound transmission is not established. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Confirm the ID of the S-AIR main unit and S-AIR sub unit (page 74). • You performed pairing the S-AIR main unit and another S-AIR sub unit. Perform pairing of the desired S-AIR sub unit (page 75). • The S-AIR main unit is pairing with another S-AIR sub unit. Cancel pairing. • Install the S-AIR main unit and S-AIR sub unit away from other wireless products. • Stop using another wireless product. • The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is connected and turn on the S-AIR sub unit. No sound is heard from the S-AIR receiver. • Check that the components are connected to analog jack of this receiver. No sound is heard from the S-AIR product. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Confirm the ID of the S-AIR main unit and S-AIR sub unit (page 74). • Confirm the pairing setting (page 75). • Install the S-AIR main unit and S-AIR sub unit closer together. • Avoid use of equipment that generates electromagnetic energy, such as a microwave oven. • Install the S-AIR main unit and S-AIR sub unit away from other wireless products. • Stop using another wireless product. • Change the “RF SETUP” setting (page 78). • Change the ID settings of the S-AIR main unit and S-AIR sub unit. • Turn off the system and S-AIR sub unit, then turn on them. • Check that headphones are not connected to the S-AIR sub unit. There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 8 m away from this S-AIR main unit. • Install the S-AIR main unit and S-AIR sub unit closer together. • Avoid use of equipment that generates electromagnetic energy, such as a microwave oven. • Install the S-AIR main unit and S-AIR sub unit away from other wireless products. • Stop using another wireless product. • Change the “RF SETUP” setting (page 78). • Change the ID settings of the S-AIR main unit and S-AIR sub unit. S-AIR function 96fiB Tuner The FM reception is poor. • Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna (aerial) as shown below. If you connect the receiver to an outdoor antenna (aerial), ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna (aerial) Receiver Ground wire (not supplied) ♦ To ground The RDS information that you want does not appear.* • Contact the radio station and find out whether they actually provide the service in question. If so, the service may be temporarily out of order. * Models of area code CEL, CEK only. Remote commander The remote does not function. • Point the remote at the remote sensor on the receiver. • Remove any obstacles in the path between the remote and the receiver. • Replace all the batteries in the remote with new ones, if they are weak. • Make sure you select the correct input on the remote. ANTENNA AM Radio stations cannot be tuned in. • Check that the antennas (aerials) are connected securely. Adjust the antennas (aerials) and connect an external antenna (aerial), if necessary. • The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning. • Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 63). • Press DISPLAY repeatedly on the receiver so that the frequency appears on the display. RDS does not work.* • Make sure that you are tuned to an FM RDS station. • Select a stronger FM station. Error messages If there is a malfunction, the display shows a message. You can check the condition of the system by the message. Refer to the following table to solve the problem. If any problem persists, consult your nearest Sony dealer. If an error message appears while you perform Auto Calibration, see “Error and warning codes” (page 32) to solve the problem. Irregular current is output to the speakers, or the upper panel of the receiver is covered with something. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. continued 97 GB Additional Information Specifications If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver’s memory may remedy the problem (page 28). However, note that all memorized settings will be reset to their initial settings and you will have to ...