Assessments - 6, GPA: 3.7
(
)
)
|
por este dispositivo também tem outras instruções :
receptor e amplificador - STR-DA3500ES (10.32 mb)
receptor e amplificador - STR-DA3500ES (19.67 mb)
receptor e amplificador - STR-DA3500ES (28.74 mb)
Facilidade de uso
The signals cannot be recorded. 23GB Getting Started Connecting components with analog audio jacks The following illustration shows how to connect a component with analog jacks, such as a tape deck, turntable, etc. Q Audio cord (not supplied) Note If your turntable has a ground (earth) wire, connect it to the (U) SIGNAL GND terminal. 24GB 4b: Connecting the video components How to hook up your Video input/output jacks to be components connected This section describes how to hook up your components to this receiver. Before you begin, see “Component to be connected” below for the pages which describe how to connect each component. Before connecting cords, be sure to disconnect the AC power cord (mains lead). After hooking up all your components, proceed to “5: Connecting the antennas (aerials)” (page 36). Component to be connected Page TV 19 With HDMI jack 26 DVD player 29 Blu-ray disc player 30 Satellite tuner, Set-top box 31 DVD recorder, VCR 32 Camcorder, video game, etc. 32 If you want to connect several digital components, but cannot find an unused input See “Enjoying the sound/images from other inputs” (page 94). Notes • When connecting optical digital cords, insert the plugs straight in until they click into place. • Do not bend or tie optical digital cord. Tip All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies. The image quality depends on the connecting jack. See the illustration that follows. Select the connection according to the jacks on your components. Note Be sure to turn on the receiver when the video and audio signals of a playback component are being output to a TV via the receiver. Unless the power is turned on, neither video nor audio signals will be transmitted. 25GB Getting Started Connecting components with HDMI jacks HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an interface which transmits video and audio signals in digital format. HDMI features • A digital audio signals transmitted by HDMI can be output from the speakers and the PRE OUT jacks on this receiver. This signal supports Dolby Digital, DTS, and Linear PCM. • Linear PCM (sampling frequency less than 192 kHz) with digital audio signals of up to 8 channels can be received with this receiver using the HDMI IN jack. • Analog video signals input to the VIDEO jack or COMPONENT VIDEO jacks can be up-converted as HDMI signals. Audio signals are not output from an HDMI OUT jack when the image is converted. • This receiver supports High Bitrate Audio (DTS-HD Master Audio, Dolby TrueHD), Deep Color and x.v.Color (x.v.Colour) transmission, extended by HDMI ver1.3. • This receiver supports the Control for HDMI function. For details, see ““BRAVIA” Sync features” (page 76). • HDMI 3 input has a better sound quality. When you need a higher sound quality, connect your component to the HDMI IN 3 (for AUDIO) jack and select HDMI 3 as input. 26BB Satellite tuner, set-top box 1 i'.'n.'il HDMI signals A Blu-ray disc player, PS3™, hard disk recorder Audio/video signals HDMI DVD player Audio/video 1 i'.'n.'il HDMI signals A © BURKHJNDISUH back ©1© CENTER © © © © © UOWTOfl 0 comi © C0MP0 2 w © COMPO1 ©’ © © © ©S' © © ASSIGN © ©» ONLY) ^© ©|© © if ©»© surrouhd|sur back §L © HDMI cable (not supplied) continued 27GB Getting Started Notes on connecting cables • Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p or Deep Color images may not be displayed properly. • Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable. • We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D component, the sound and/or the image may not be output. Connect other audio cords or digital connecting cords, then set “Input Assign” in the Input menu when the sound is not output correctly. Notes on HDMI connections • An audio signal input to the HDMI IN jack is output from the speaker output jacks, HDMI OUT jack and PRE OUT jacks. It is not output from any other audio jacks. • A video signal input to the HDMI IN jack can only be output from the HDMI OUT jack. The video input cannot be output from the VIDEO OUT jacks or MONITOR OUT jacks. • The audio and video signals of HDMI input are not output from the HDMI OUT jack while the receiver menu is displayed. • When you want to listen to the sound from the TV speaker, set “Audio Out” to “TV+AMP” in the HDMI settings menu. If set to “AMP”, the sound is not output from the TV speaker. • DSD signals of Super Audio CD are not input and output. • Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. Check the setup of the connected component if an image is poor or the sound does not come out of a component connected via the HDMI cable. • Sound may be interrupted when the s...