Assessments - 2, GPA: 4.5
(
)
)
|
Fotos e especificações Sony STR-DN2010 |
por este dispositivo também tem outras instruções :
receptor e amplificador - STR-DN2010 (16.81 mb)
receptor e amplificador - STR-DN2010 (20.76 mb)
Facilidade de uso
Do not connect other microphones to this jack. • Set “Sur Back Assign” to “BI-AMP” in the Speaker Settings menu if you use bi-amplifier connection (page 106). • Set “Sur Back Assign” to “SPEAKER B” in the Speaker Settings menu if you use speakers front B connection (page 41). • Pair the surround amplifier to S-AIR main unit if you want to use surround amplifier. • Make sure the speaker output is not set to “SPK OFF” (page 42). • Disconnect the headphones. • Remove any obstacles in the path between the optimizer microphone and the speakers to avoid measurement errors. • Make sure the environment is quiet to avoid the effect of noise and get a more accurate measurement. • Select the seating position as position 1, 2 or 3 to save the Auto Calibration result (page 108). Notes • During the measurement, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood. • If the muting function has been activated before you perform Auto Calibration, the muting function will be set to off automatically. • The measurements may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. o • O => -o Optimizer microphone O DOOOODOO îm AUTO CAL MIC Example of using surround back speakers 1 Select the speaker pattern (page 40). If you connect front high speakers, select the speaker pattern that has front high speakers (5/1.1 or 4/1.1) each time you perform Auto Calibration. Otherwise, the characteristics of the front high speakers cannot be measured. 2 Connect the supplied optimizer microphone to the AUTO CAL MIC jack. 3 Set up the optimizer microphone. Place the optimizer microphone at your seating position. Use a stool or tripod so that the optimizer microphone remains at the same height as your ears. continued 43GB Preparing the Receiver On setting up the active subwoofer • When a subwoofer is connected, turn on the subwoofer and turn up the volume beforehand. Turn the LEVEL to just before the mid-point. • If you connect a subwoofer with a crossover frequency function, set the value to maximum. • If you connect a subwoofer with an auto standby function, set it to off (deactivated). Note Depending on the characteristics of the subwoofer you are using, the setup distance value may be further away from the actual position. 1 Press GUI MODE. After “GUI ON” appears on the display for a while, the GUI menu appears on the TV screen. Press MENU if the GUI menu does not appear on the TV screen. 2 Press v/v repeatedly to select “w Settings”, then press 0 or b. The Settings menu list appears on the TV screen. 44GB 3 Press v/v repeatedly to select “Auto Calibration”, then press ©. 4 Press v/v repeatedly to select “Calibration Start”, then press ©. The screen on which you can select the item to be measured appears. w Auto Calibration Select items to be measured. O ( Speaker Distance ) 0 Speaker Level ► 0 Frequency Characteristic C return) Back 5 Press v/v repeatedly and © to uncheck the items you do not want to measure, then press b. The confirmation screen, asking whether you are ready to start measurement, appears. 6 Press 0 to select “Start”. The measurement starts in five seconds. The measurement process will take approximately 30 seconds with a test tone. Wait until the measurement process completes. When the measurement ends, a beep sounds and the screen switches. 7 Note If an error code appears on the screen, see “Message list after Auto Calibration measurement” (page 48). Press v/v repeatedly to select the item you want, then press Item and explanation Retry Performs the Auto Calibration again. Save Saves the measurement results and exits the setting process (page 46). Warning Displays warning concerning the measurement results. See “Message list after Auto Calibration measurement” (page 48). Phase* Displays the phase of each speaker (in phase/ out of phase). Distance Displays the measurement result for speaker distance. Level Displays the measurement result for speaker level. Exit Exits the setting process without saving the measurement results. To save the measurement results, follow the steps in “3: Saving the measurement results” (page 46). If you want to check error code or warning message, see “Message list after Auto Calibration measurement” (page 48). continued 45BB Preparing the Receiver * When the speaker(s) is (are) out of the phase, “Out” is displayed on the TV screen. The “+” and “—” terminals of the speaker may be connected the other way around. However, depending on the speakers, “Out” appears on the TV screen even though the speakers are connected properly. This is because of the speakers’ specifications. In this case, you can continue to use the receiver. Tips • Operations other than turning the receiver on or off are deactivated during the measur...