Assessments - 3, GPA: 3.7
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Set them apart and perform the measurement again. Warning 43 The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the measurement in a quiet environment. No Warning There is no warning information. Tip Depending on the position of the subwoofer, the measurement results may vary. However, there will be no problems even if you continue to use the receiver with that value. Configuring the network settings of the receiver The network settings for the receiver must be set correctly to use the Home Network, SEN, AirPlay, and PARTY STREAMING functions. Using a wireless LAN connection There are several connecting methods you can use to set up a wireless network: searching for an access point, using a WPS connecting method (either the push-button method or the PIN code method), or manual setting. Notes • Make sure not to use the wireless LAN function where medical equipment (such as a pacemaker) is used or where the use of wireless communication is prohibited. • Before connecting to your home network, you need to prepare a wireless LAN router/access point. For details, refer to the operating instructions of the device. • Depending on your home network environment, the wireless LAN router/access point may have been set up such that it cannot be connected using WPS, even though it is compatible with WPS. For details on whether your wireless LAN router/ access point is compatible or not compatible with WPS, and on the setup of a WPS connection, refer to the operating instructions of your wireless LAN router/access point. •You may encounter setup difficulties if the receiver and the wireless LAN router/access point are located too far from each other. If you do, move the devices closer to each other. continued 43GB Preparing the Receiver Searching for an access point and setting up a wireless network (Access Point Scan method) You can set up a wireless network by searching for an access point. To set up the network using this connection method, you will be required to select or enter the following information. Check the following information in advance, and record it in the space provided below. □ The network name (SSID*1) that identifies your network*2. (This will be needed in step 7.) □ If your wireless home network is secured by encryption, the security key (WEP key, WPA/WPA2 key) for your network*2. (This will be needed in step 8.) SSID (Service Set Identifier) is a name that identifies a particular access point. *2 This information should be available from a label on your wireless LAN router/access point, from the operating instructions, from the person who set up your wireless network, or from the information provided by your Internet service provider. 1 Press MENU. The menu is displayed on the TV screen. 2 Press v/v repeatedly to select “w Settings”, then press © or b. 3 Press v/v repeatedly to select “Network”, then press 0. 4 Press v/v repeatedly to select “Settings”, then press 0. 5 Press v/v repeatedly to select “Wireless LAN Settings”, then press 0. If “Change Setting?” appears on the TV screen, select “OK”, then press ©. 6 Press v/v repeatedly to select “Access Point Scan”, then press 0. The receiver starts searching for access points, and displays a list of up to 30 available network name (SSID). 7 Press v/v repeatedly to select the network name (SSID) you want, then press 0. The security setting display appears on the TV screen. 8 Enter the security key (WEP key, WPA/WPA2 key), then press 0. By default, the security key appears as “*****”. Press DISPLAY repeatedly to encrypt and disclose the security key. “IP Settings” appears on the TV screen. 9 Press v/v repeatedly to select “Auto”, then press 0. The proxy setting display appears on the TV screen. 44BB When using a fixed IP address Select “Manual”, then press ©. The IP address input display appears on the TV screen. Press SHIFT, then press numeric button to enter the value for “IP Address”, and then press ©. Then, enter the value for “Subnet Mask”, “Default Gateway”, “Primary DNS” and “Secondary DNS”. The proxy setting display appears on the TV screen. 10 Press v/v repeatedly to select “Do Not Use”, then press 0. The confirmation display appears on the TV screen. When using a proxy server Select “Use”, then press ©. The proxy address input display appears on the TV screen. Press SHIFT, then press numeric/text button to enter the value for “Proxy Address”, and then press ©. Then, enter the value for “Port Number”. The confirmation display appears on the TV screen. 11 Press v/v repeatedly to select “OK”, then press 0. “Connecting” flashes on the TV screen. “Complete!” appears after the network settings are completed and “,?iV’ lights up on the display panel. To return to the Network Settings menu, press ©. (Depending on the network environment, the network settings may take some time.) 12 Perform the server settings. To listen to audio content store...