Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
* Leave clearance of more than 10 cm (4 in.) to the left and More than right, more than 50 cm (20 in.) above and more than 10 cm (4 in.) in front and rear of the unit. Also, do not close the More than 10 cm (4 in.) surroundings of the unit tightly when it is mounted on a rack. 10 cm (4 in.) • The ventilation fan of this unit has been designed to intake external air into the unit. If curtain or a piece of paper is attracted by the air intake, the internal temperature will rise and protection circuitry will be activated. In this case, the sound will not be output. More than More than 10 cm (4 in.) 10 cm (4 in.) Connections Make connection as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Do not plug in the power lead until all connections are completed. 7 Connections of speaker cords Connection of banana plugs (Except for some countries, like Singapore, etc.) 1 Secure. 2 Insert. Connections of speaker cords 1 Strip coating. 2 Loosen. 3 Insert. 4 Secure. • Sound will not be heard if the speaker terminal is not fully secured. For U.S.A. CAUTION: If the unit is used in the U.S.A., please read the supplement to the operating instruction entitled “Connection of speaker cords”. Warning! Particular attention must be given to making good electrical contact at the amplifier-output and speaker terminals. Poor or loose connections can cause sparking or burning at the terminals because of the very high power that the amplifier can deliver. CAUTIONS: •Connect all cords firmly. If connections are loose, there could be loss of sound or noise produced. •Never attempt to connect two or more speaker cords to a single speaker terminal. •Never short-circuit the + and - speaker cords. •If the left and right speakers are connected inversely or if the speaker cords are connected with reversed polarity, the sound becomes unnatural with ambiguous acoustic image positioning. Be sure to connect the speakers and speaker cords correctly. 3 3 EN 7 7 This is the ‘standard’ stereo operation mode, with the amplifier driving 2 speakers in stereo (such as the Surround Back Left and Surround Back Right speakers in a THX Surround EX® home theater system). The amplifier delivers its rated stereo power output into each speaker. 1 Make sure that the KMF-X9000’s power cord is unplugged from the wall outlet before making any connections. 2 According to the speakers to be used, set the speaker impedance selector switch as follows: • For 2 . speakers: Set the 2. (STEREO)/6. OVER switch to 2. (STEREO) and 6. OVER/2. switch to 2.. • For 6-16 . speakers: Set the 2. (STEREO)/6. OVER switch to 6. OVER and 6. OVER/2. switch to 6. OVER. 3 Connect the amplifier as shown in the diagram. CLIP INDICATOR CD 2 / TAPE 2 MONITOR SURROUND BACK 96kfsDISCRETE 6.1 MATRIX 6.1 NEO : 6 PRO LOGIC DTS-ES Preamplifier Audio cord (supplied) To wall AC outlet Speakers (2.-16.) * In the case of 2 . ON : +12 V OFF : OPEN (or GND) NC GND KRF-X9995D For RELAY CONTROL connection to KRF-X9995D or other compatible unit, see page 6.LeftRight In the case of 6 . Stereo mini-plug cord (supplied) For 12 V RELAY CONTROL, see page 6. (R SURROUND (L SURROUND BACK) BACK) * If you connect more than one pair of speakers to the KMF-X9000, move the 2. (STEREO)/6. OVER (THX) switch to the 2. (STEREO) position. The amplifier’s performance is not THX®-certified when the switch is set in the 2. (STEREO) position. Now you can plug the power cord of this unit into the AC outlet! CAUTION: Before reconnecting a speaker cord or switching a selector switch, turn OFF the power and unplug the power cord to avoid malfunctions or damage to the unit. 4 4 EN 7 7 In this configuration, the KMF-X9000’s two individual channels operate together to drive a single speaker (such as a subwoofer) in mono. This allows the amplifier to deliver more than double the power of one of its channels to the speaker. 1 Make sure that the KMF-X9000’s power cord is unplugged from the wall outlet before making any connections. 2 According to the speakers to be used, set the speaker impedance selector switch as follows: • For 6-16 . speakers: Set the 2. (STEREO)/6. OVER switch to 6. OVER and 6. OVER/2. switch to 2.. 3 Connect the amplifier as shown in the diagram. • Make sure to connect the audio input cable to the MONO/BTL input. Except for Europe Note: Since bridged operation produces enough output power to pose a small risk of electrical shock from the speaker terminals, please attach the terminal cover as shown in the diagram below: KRF-X9995D CLIP INDICATOR CD 2 / TAPE 2 MONITOR SURROUND BACK 96kfsDISCRETE 6.1 MATRIX 6.1 NEO : 6 PRO LOGIC DTS-ES Except for Europe Mount the supplied speaker terminal cover using the two screws that are attached to the unit. When a monaural pre-out signal is to be connected, be sure to connect it to the MONO/BTL terminal. Audio cord (not supplied) Stereo mini-plug cord (supplied) To wall AC outlet Subwoofers (6.-16.) For 12 V...