Assessments - 3, GPA: 4.3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
(See “Connecting video components”.) ! LD player To connect an LD player with a DIGITAL RF OUT, connect the LD player to the RF digital demodulator (Commercially available). Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of this model. Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) 13 EN Setting up the system Setting up the system CENTERFRONT + - CR L RED WHITE GREEN VR-905/KRF-V5090D SURROUND + - R GRAY L BLUE SURROUND BACKSURROUND + - VR-906/KRF-V6090D R GRAY L BLUE BROWN SPEAKERS (8 SPEAKERS (8-16.)SPEAKERS (8-16.) SUB WOOFER PRE OUT PRE OUT SURR BACK L* SURR BACK R PRE OUT SURR BACK L /SURR BACK SURR BACK R VR-906/KRF-V6090D *VR-906/KRF-V6090D: SURR BACK L /SURR BACK Center Speaker Front Speakers Right Left Powered Subwoofer Surround Back Speakers RightLeft Surround Back Speaker When connecting a single Surround Back speaker through a power amplifier to PRE OUT jack, connect it as above and select “SPEAKER” at speaker settings. & When connecting a Surround Power amplifier Power amplifier VR-906/ KRF-V6090D only When using both Surround Back Left and Right speakers, select “PRE OUT” at speaker settings. & Right Left Surround Back speaker to this terminal, Surround Speakers Back Speaker select “SPEAKER” at speaker settings. & To make sure that each speaker has been connected properly, pay attention to the test tone from each speaker. Refer to “4 Adjust the speaker volume level ”. & 14 EN Setting up the system Setting up the system 3Insert the cord. 4Return the lever. 2Push the lever1Strip coating. • Never short circuit the + and – speaker cords. • If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly. Speaker impedance After confirming the speaker impedance indications printed on the rear panel of this model, connect speakers with matching impedance ratings. Using speakers with a rated impedance other than that indicated on the rear panel of this model could result in malfunctions or damage to the speakers or this model. Speaker placement * For Surround Back speaker, you may place either two Surround Back speakers (Surround Back Left speaker and Surround Back Right speaker) for 7.1 channel surround sound system or one Surround Back speaker for 6.1 channel surround sound system. Front speakers : Place to the front left and right of the listening position. Front speakers are required for all surround modes. Center speaker : Place front and center. This speaker stabilizes the sound image and helps recreate sound motion. Required for surround playback. Surround speakers : Place to the direct left and right, or slightly behind the listening position at even heights, approximately 1 meter above the ears of the listeners. These speakers recreate sound motion and atmosphere. Required for surround playback. Subwoofer : Reproduces powerful deep bass sounds. Surround Back speaker/s : Place the speaker/s directly at the rear of the listening position. The optimum position depends mainly on the room condition. • Although the ideal surround system consists of all the speakers listed above, if you don't have a center speaker or a subwoofer, you can divide those signals between the available speakers in the speaker settings steps to obtain the best possible surround reproduction from the speakers you have available. ^ Front speaker Subwoofer Center speaker Listening position *Surround Back speaker Surround speaker *Surround Back Left speaker *Surround Back Right speaker *Optional in this model. The broadcast reception cannot be made unless the antennas are connected. Connect the antennas correctly as instructed below. AM loop antenna Place the supplied loop antenna as far as possible from the receiver, TV set, speaker cords and power cord, and adjust the direction for best reception. AM antenna terminal connections 1 Push lever. 2 Insert cord. 3 Release lever. FM indoor antenna The supplied indoor antenna is for temporary use only. For stable signal reception we recommend using an outdoor antenna. Disconnect the indoor antenna when you connect one outdoors. FM antenna terminal connections Insert the connector. KRF-V6090D/ VR-906/VR-905 KRF-V5090D FM outdoor antenna Lead the 75. coaxial cable connected to the FM outdoor antenna into the room and connect it to the FM 75. terminal. GNDAM FM 75.ANTENNA Use an antenna adapter (Commercially available) Attach to the stand AM loop antenna FM indoor antenna FM outdoor antenna VR-906/ VR-905 KRF-V6090D/ KRF-V5090D 15 EN Preparing for surround sound Speaker settings To enable you to obtain optimum enjoyment from this model’s listening modes, make sure to complete the speaker settings (Subwoofer, Front, Center, Surround and Surround Back speakers) as described below. MULTI CONTROL SETUPPOWER ON/OFF ON/STANDBY(KRF-V6090D/ KRF-V5090...
Este manual também é adequado para os modelos :receptor e amplificador - KRF-V6090D (1.41 mb)
receptor e amplificador - VR-905 (1.41 mb)
receptor e amplificador - VR-906 (1.41 mb)