e Press [SETUP] to get into the setup mode of the selected element. To exit the setup mode Select "EXIT" in the step . and press [SETUP]. English 17 Speaker settings Speaker setup ("SP SETUP") This sets up the speakers according to the speaker system in use. Speaker setup is required every time the speaker system is changed. oe See (&) and select "SP SETUP". . Use [MULTI CONTROL 5/.] to select the subwoofer setting. Speaker Display Selection Subwoofer "SUBW ON" "SUBW OFF" With Subwoofer Without Subwoofer e Press [SETUP]. ® Repeat steps . – e for the rest of the speaker setting. Speaker Display Selection Front speaker "FRNT LRG" "FRNT NML" Large size front speaker Average size front speaker "CNTR NML" Average size center speaker Center speaker "CNTR LRG" Large size center speaker "CNTR OFF" No center speaker is connected. "SURR NML" Average size surround speaker Surround speaker "SURR LRG" Large size surround speaker "SURR OFF" No surround speaker is connected. Subwoofer re-mix* "RMX ON" "RMX OFF" Subwoofer re-mix is on. Subwoofer re-mix is off. * The function for adding the bass of other channels to the subwoofer channel according to the speaker setup. † Go to the next setting, "TEST TONE". • If you wish to exit the setup mode, see &. Notes: • When "SUBW OFF" is selected, the front speakers are automatically set to "FRNT LRG". • For "FRNT LRG" selection, no sound will be heard from subwoofer even it is set to ON. However, if you select "RMX ON", you will be able to hear sound from the subwoofer. • When in STEREO mode, the sound goes directly to front speakers. • If "FRNT NML" is selected, "CNTR LRG" cannot be selected. • If "CNTR NML" or "CNTR OFF" is selected, "SURR LRG" cannot be selected. Adjusting the speaker level ("TEST TONE") From your usual listening position, adjust the volume output of each speaker. The output level from each speaker should be the same. oe See (&) and select "TEST TONE". . Use [MULTI CONTROL 5/.] to select either "AUTO" or "MANUAL". Display Selection The test tone is heard from the speakers one after another with "AUTO" 2 seconds each. "MANUAL" The test tone is heard from the speaker you have selected. e Press [SETUP]. ® Adjust the output level. If you select "AUTO": When you hear the test tone from the speaker which you wish to adjust, use [MULTI CONTROL 5/.] and adjust the volume of the test tone. When you finish adjusting, press [SETUP]. If you select "MANUAL": Use [MULTI CONTROL 5/.] to adjust the volume of the test tone and press [SETUP]. You will hear the test tone from the next speaker. † Go to the next setting, "DISTANCE". • If you wish to exit the setup mode, see &. 18 KRF-V5300D Distance setting ("DISTANCE") This sets the distance from each speaker to the listening position. oe Measure the distance from the listening position to each speaker and jot down in the table below. Speaker Indicator Distance from the listening position Front speaker (left) "L" feet (meters) Center speaker "C" feet (meters) Front speaker (right) "R" feet (meters) Surround speaker (right) "RS" feet (meters) Surround speaker (left) "LS" feet (meters) Subwoofer "SW" feet (meters) . See (&) and select "DISTANCE". e Use [MULTI CONTROL 5/.] to select the distance to the front speaker. • Adjustment will start from front left speaker. Indicator ® Press [SETUP]. † Repeat steps e – ® to input the distance for the rest of the speaker. . Go to the next setting, "LFE LVL". • If you wish to exit the setup mode, see &. Low frequency effects level ("LFE LVL") Low frequency effect signal is used exclusively for giving the field effect of bass tone in the Dolby Digital and DTS signal. oe See (&) and select "LFE LVL". . Use [MULTI CONTROL 5/.] to adjust the low frequency effect level. • The level is adjusted from 0dB to -10dB in 1dB step decrements. e Press [SETUP]. • The setup is complete when the "EXIT" indication appears. ® Press [SETUP] to exit the setup mode. English 19 Normal Playback Preparing for playback Some preparatory steps are needed before starting playback. INPUT SELECTOR SPEAKERS ON/OFF LISTEN MODE INPUT MODE LISTEN MODE RECEIVER Input source keys Turning on the power oe Turn on the power to the related components. . Press [ RECEIVER] to turn on the receiver unit. Setting the speaker status (main unit only) Press [SPEAKERS ON/OFF] to switch the speaker on or off. The speaker indicator lights up when set to on. Note: • Set Speakers to OFF for stereo playback. When Speakers is set to ON again, the listen mode remains in stereo if the input signal is digital. Selecting the input mode (main unit only) If you have selected a component connected to the DIGITAL IN jacks (CD/DVD, VIDEO2 and DVD/6CH INPUT), make sure that the input mode setting is correct for the type of audio signal to be used. oe Use [INPUT SELECTO...
)
