Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
2Press the numeric key to enter "9 - 9 - 1". • The LED will blink twice. 3Point the remote control at the TV and slowly alternate between pressing the SRC Power and TV key. • Stop when the TV turns on/off. • In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 4Press the Remote Setup key once to lock in the code. 5To search for the codes of your other components, repeat steps 1 through 4, but substitute the appropriate key (i.e., DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX, PHONO). • PHONO key has to be re-assigned to another key before a setup code can be programmed. Checking the codes If you have setup the remote control using the procedures described in “Searching for your codes”, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1Press the TV key once. Next, press and hold the Remote Setup key until the LED blinks twice, then release the Remote Setup key. 2Press the numeric key to enter "9 - 9 - 0". • The LED will blink twice. 3To view the code for the first digit, press “1”once. Wait for 3 seconds, counts the number of times the LED blinks (e.g., blinks=3) and write down that number. • If a code digit is “0”, the LED will not blink. Continued to next page 35EN ENGLISH Basic remote control operations for other components ENGLISH Basic remote control operations for other components ENGLISH 4Repeat step 3three more times for the remaining digits. Use “2”for the second digit, “3”for the third digit, and “4”for the fourth digit. 5To check the codes of your other components, repeat steps 1 through 4, but substitute the appropriate key (i.e., DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX, PHONO) for the component you are checking. • As suggested earlier on, write down each of the four-digit code. • PHONO key has to be re-assigned to another key before a setup code can be programmed. Re-assigning device keys The remote control can be setup to control second TV or VCR, or any combination of eight home entertainment components. For example, to control the operation of two different VCR using the remote control, the user need to re-assign the unused VID2 key to operate the second VCR(VID1) as follows: 1Press and hold the Remote Setup key until the LED blinks twice, then release the Remote Setup key. 2Press the numeric key to enter "9 - 9 - 2". • The LED will blink twice. 3Press VID1 key once, then press the VID2 key once. • The user now can operate VID2 as a second VCR along with VID1. • Refer to the table in the previous page for the combination of source keys and the other components assignment. fi 4To re-assign other device keys, repeat steps 1through 3 by substituting the key sequence from the below chart for the most popular components: To re-assign key Sequence Perform TV as 2nd VID1 key Remote Setup - 9- 9 - 2 VID1 - TV TV as 2nd VID2key Remote Setup - 9 - 9 - 2 VID2 - TV TV as 2nd CD/DVD key Remote Setup - 9 - 9 - 2 CD/DVD - TV TV back to TV key Remote Setup - 9 - 9 - 2 TV - TV VID1 as 2nd TV key Remote Setup - 9 - 9 - 2 TV - VID1 VID1 as 2nd VID2 key Remote Setup - 9 - 9 - 2 VID2 - VID1 VID1 as 2nd CD/DVD key Remote Setup - 9 - 9 - 2 CD/DVD - VID1 VID1 back to VID1 key Remote Setup - 9 - 9 - 2 VID1 - VID1 5To clear the re-assignment and reset the remote control to its original operation mode: 1 Press and hold the Remote Setup key until the LED blinks twice, then release the remote setup key. 2 Press the numeric key to enter "9 - 9 - 2". 3 Press VID2 key twice. • When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control in order to control the new component. • If an invalid key sequence is entered, the LED blink once and return to normal operation. • When in Tuner mode, re-assignment is not available. Operating other components This operation lets you operate the registered components. KENWOOD audio components with system control turn on and off automatically with the receiver via the system control connections. Source keys SRC Power 1Use the Source keys to select the component you desire. • Pressing the source keys also changes the input selector on the receiver. • When you operate your registered cassette deck, CD player, DVD player, Cable, Satellite, DTV Decoder, VCR or TV, go to step 2. • When you operate the CD player, Cassette deck, MD player, or Tuner with system control connection, go to step 3. 2Press the SRC Power key. • To return to the receiver operation mode, press the TUNER key for more than 3 seconds. 3Press the operation keys you desire. w The remote control mode remains at the selected input. If you wish to operate another component, repeat step 2 or 3. Note • Be sure to point the remote control at the remote sensor on the receiver when you want to operate KENWOOD components connected by system control cords. Otherwise, p...