Assessments - 3, GPA: 4 ( )

Fabricante : Kenwood Arquivo Tamanho: 1.26 mb Arquivo Nome : Língua de Ensino:

If this happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition. • Please note that resetting the microcomputer will clear the contents of the memory and return the unit to the state it was in when it left the factory Unplug the power cord from the wall outlet, then plug it back in while holding down the POWER ON/ STANDBY key. For the U.S.A. and Canada With the power cord plugged in, turn the POWER ON/OFF key OFF. Then, while holding down the ON/STANDBY key, press POWER ON/OFF key. For other countries Amplifier Symptom Cause Remedy No sound from the speakers. • The speaker cords are disconnected. • VOLUME is set to the minimum position. • MUTE is ON. • The SPEAKERS switches are set to OFF. • Connect them properly referring to “Connecting the speakers”. # • Adjust the volume to a proper level. • Turn OFF the MUTE. ( • Set the SPEAKERS switch to ON. * The standby indicator blinks and sound is not output. • Speaker cords are short-circuited. • Turn the power off, eliminate the shortcircuiting, then turn on the power again. Sound is not output from one of the speakers. • The speaker cord is disconnected. • Connect it properly referring to “Connecting the speakers”. # Sound is not output from the surround speakers and / or the center speaker, or their sound is very soft. • The surround speaker cords and/or the center speaker cord is disconnected. • A surround mode has not been activated. • The surround and/or center volume controls are set to the minimum level. • Connect it properly referring to “Connecting the speakers”. # • Select a surround mode. • Adjust the speaker levels using the test tone. & When playing a Dolby Digital source signal using a DVD player, the sound is cut off soon after it starts. • There are many possible causes for this problem, depending on the type of DVD player used. • Set the input mode to digital manual before starting playback of the Dolby Digital source. 8 No sound is produced during playback from a DVD player. • The input mode is set to digital manual. • Press the INPUT MODE key to select to full auto mode. 8 A video source cannot be recorded normally. • The software is copy-guarded. • Copy-guarded video software cannot be recorded. Tuner Symptom Cause Remedy Radio stations cannot be received. • No antenna is connected. • The broadcast band is not set properly. • The frequency of the desired station is not tuned. • Connect an antenna. $ • Set the broadcast band properly. • Tune the frequency of the desired station. . Interference. • Noise due to ignition of an automobile. • Noise due to interference from an electric appliance. • Noise due to a nearby TV set. • Install the outdoor antenna away from the road. • Turn off the power to the appliance. • Install the receiver farther away from the TV. A station which was preset cannot be received by pressing the corresponding numeric key. • The preset station belongs to a frequency that cannot be received. • The preset memory was cleared because the power cord had been unplugged for a long period of time. • Preset a station with a receivable frequency. • Preset the station again. 30EN In case of difficulty In case of difficulty Symptom Cause Remedy Remote control operation is not possible. • The remote control is set to a different operation mode. • Batteries are exhausted. • The remote control unit is too far away from the main system, controlling angle is too large, or there is an obstacle between the receiver and the remote. • The audio cords and system control cords are not connected properly. • No tape or CD is placed in the source component. • An attempt is made to play a tape which is being recorded in the cassette deck. • Press the source select keys or DVD POWER keys to select the appropriate operation mode. • Replace with new batteries. • Operate the remote control unit within the controllable range. • Connect properly referring to “Setting up the system”. • Place the tape or CD in the source component which you want to play. • Wait for recording to complete. 31EN Caution : Read this page carefully to ensure safe Caution : Read this page carefully to ensure safe operation. For the U.S.A and Canada CENTER (1 kHz, 0.7% T.H.D. at 8. one channel driven) .. 50 W SURROUND (1 kHz, 0.7% T.H.D. at 8. one channel driven) AUDIO section (VR-705/715) ................................................................................... 50 W + 50 W Rated power output during STEREO operation 100 watts per channel minimum RMS, both channels driven, at 8.from 40 Hz to 20 kHz with no more than 0.7% total harmonic distortion. (FTC) Effective power output during SURROUND operation FRONT (40 ~ 20 kHz, 0.7% T.H.D. at 8. one channel driven) ............................................................................... 100 W + 100 W CENTER (40 ~ 20 kHz, 0.7% T.H.D. at 8. one channel driven) .............................................................................................. 100 ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :