Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Insert the smart card with the chip facing up. Push the smart card into the slot as far as it will go. The end of the card will be visible outside the slot. New and updated information may be downloaded onto the smart card from time to time. 46 Connecting your receiver There are several ways you can connect and incorporate your digital receiver into your existing audio/video equipment set up. Before starting to connect: - Unplug all equipment (TV set as well as VCR and/or DVD or DVD+R if required) from the mains. -Do not connect your digital receiver to mains supply now. - Check your current wiring: you may not need to modify your existing audio/video set up connections if they already match the connection diagrams below. - Depending on your exiting set up, choose the best suited connection method for incorporating your digital receiver. When adding new equipment, be sure to refer to the related installation instructions of the manual of the respective devices. Connecting to TV and VCR/DVD player using SCART Support EN to AC outlet PHILIPSTV set VCR/DVD Cable Receiver IN FROM ANT OUT TO ANT EXT 1 EXT 1 EXT 2 EXT 2 Cable Wall socket For optimum configuration Screw the adapter supplied with your receiver on the “RF IN” connector of the rear panel. Use the antenna cord type F-IEC supplied to connect your receiver to the VCR/DVD. Use the SCART cable supplied to connect your receiver to the TV set. For best DVD/VCR viewing, connect the DVD/VCR SCART EXT 1 directly to the TV set SCART. 47 Connecting to your audio equipment EN Cable Receiver to AC outlet Analogue input Audio equipment LR AUDIO Digital input AB Analogue connection (A) Connect the L/R audio output sockets to the relevant L/R audio input sockets of your audio equipment using a double CINCH cable (not supplied). Consult the user manual of your audio equipment to choose the proper analogue audio inputs. Digital connection (B) Connect the audio “SPDIF” output socket to the relevant digital audio input socket of your audio equipment using a single CINCH cable (not supplied). Consult the user manual of your audio equipment to choose the proper digital audio input. With this connection set up you can only control the audio volume up/down and mute from your audio equipment. 48 First installation For fast and successful start-up, check that your receiver is connected to the wall socket, TV set and other equipment according to the diagrams in chapter Connecting your receiver. Switch on the receiver and TV set. The welcome screen appears, then the First installation screen. First installation settings -Set your favourite menu language and press OK. -Set appropriate values for the following: • Network ID: applicable network ID as indicated by your operator. See operator booklet for the right decimal value to be entered for your region. • Frequency: broadcast frequency predefined or entered manually as indicated by your operator (see operator booklet) • Symbol Rate: predefined value, which should not be modified unless requested by your operator • Modulation: predefined modulation type, which should not be modified unless requested by your operator. Symbol rate and modulation may be modified manually upon request by your operator. -Press OK to start scanning for channels. Channel scanning During the scanning process, the following information is reported on screen: • number of TV and Radio channels detected • name of the network detected • level and quality of reception of the signal. When scanning has been successfully completed, a completion message is displayed, and then the receiver tunes to the first channel in the list. EN 49 EN Scanning failure In case of channel scanning failure, a failure message is briefly displayed, and then the main menu appears (in case of first attempt). Select Setup then Channels installation, and proceed as described in paragraph Channels installation to launch a new scan. If installation fails again, the Setup sub menu appears; select Channels installation, and proceed as described in paragraph Channels installation. Before starting a new scan It is recommended to do the following checks: • connections to your receiver (see chapter Connecting your receiver) • number of channels available in the region corresponding to your area. • network settings provided by your operator (see operator booklet). If the same failure message appears after a while, refer to chapter Troubleshooting. Contact your cable operator if the problem remains. 50 General Viewing Functions EN This section describes the basic functions available while watching digital TV or listening to digital radio. For general menu navigation, see Settings. Receiver wake up Your receiver is in standby. Press P+, P-, or any number key of the remote control. Alternatively, press y or t on the front panel. Your receiver, as any electronic equipment, consumes power. In order to reduce power consumption, please switch your receiver to standby whenever you are not using it. For m...