Click the User Control link on the left side of the page. The User Control page appears (figure 4-8). 2. Click the button for the input containing the main image source. 3. Click the PIP Setup link on the left side of the page. The PIP Setup page appears (figure 4-10). 4. Use the drop-down menu to set the size of the subordinate (PIP) picture. 5. Use the drop-down menu to choose the appropriate PIP input (See chapter 2, Installation and Operation, for information on PIP window selection). The attributes window for the PIP appears, as shown below. Figure 4-11 — PIP “On” 6. Once the PIP window is selected, its picture control settings are available on the PIP Setup page. (figure 4-10). N When PIP is activated, the adjustments under the User Control page are also applied to the PIP window. 7. Define the attributes for the PIP. Use the Swap button to exchange the size and position of the main and PIP windows. Audio (DVS 304 A only) Use the Audio Follows radio button, shown right, to assign audio to either the main image or the PIP image. 4-12 DVS 304 • Ethernet Control DVS 304 A Appendix Menu System DVS 304 Menu System Menu System DVS 304 Menu System Default cycle menu Default Cycle 2 sec. Power on EXTRON DVS 304 2 sec. INPUT 1 COMPOSITE 60-736-01 FW ver. 1.xx 2 sec. 2 sec. OUTPUT 1024 x 768@60 Main menu Default Cycle 2 sec. (Audio models only) MENU TO EXIT MENU MENU NEXT START AUTO IMAGE ON IN1 MENU MENU INPUT CONFIG MENU PICTURE CONTROL MENU OUTPUT CONFIG MENU AUDIO CONFIG MENU MEMORY PRESETS Power on DVS 304 2 sec. FW ver. 1.xx 2 sec. EXTRON INPUT 1 60-736-01 COMPOSITE 2 sec. OUTPUT 1024 x 768@60 IP CONFIG MENU MENU ADVANCED CONFIG PRESS NEXT A-2 DVS 304 • Menu System DVS 304 • Menu System A-3 Start Auto Image menu Default Cycle INPUT 1 COMPOSITE 2 sec. 2 sec. OUTPUT 1024 x 768@60 MENU START AUTO IMAGE ON IN1 PRESS NEXT TO START NEXT NEXT Input Configuration menu START AUTO IMAGE ON IN1 INPUT CONFIG MENU NEXT INPUT 2 YUVi INPUT 4 NEXT RGB SCALED NEXT ASPECT RATIO 4x3 TTLPIX PHASE XXXX 08 NEXT NEXT NEXT H START V 50 33 H ACTIVE V NEXT XXX XXX FILM MODE ON SDI INPUT NEXT <*> 1 2 3 4 NEXT Displays only when applicable Displays only when applicable Displays only when applicable SDI DE-INTER FIELD STNDRD NEXT Displays only when applicable Select video format • Composite • S-video • YUVi • YUVp • YUV Auto Assign SDI to Input # • 1, 2, 3, 4, * (none) Select video format • Composite • S-video • RGBcvS • YUVi • YUVp • RGB scaled • RGB pass • Auto detect Input 1 can only accept composite video. Input 3 can only accept S-video. Only Inputs 2 and 4 can be configured for different video types, although an SDI input can be assigned to any input. The SDI input signal can be assigned to any input. Once assigned to a specific input, only an SDI signal can be accepted on that input. SDI can be disabled by selecting the *. Aspect ratio options • 4 x 3 • 16 x 9 For YUVp or RGB input only Total pixels Specify the width in pixels of the total image area sampled. Pixel phase Adjust the pixel sampling point for a selected input. Horizontal start Select for the left edge of the active video. Vertical start Select for the top edge of the active video. Horizontal active pixels Specify the width in pixels of the active image area sampled. Vertical active lines Specify the height in lines of the active image area sampled. Film mode Turn On or Off for low resolution devices. Not for use with YUVp or RGB inputs. N NSDI De-interlacing options: • Field Standard • Field Flip Picture Control INPUT CONFIG MENU NEXT PICTURE CONTROL H POS V 000 000 NEXT NEXT COLOR TINT 064 064 NEXT DETAIL 064 H PAN V 000 000 NEXT NEXT NEXT NEXT ZOOM 100% H SIZE V 1024 768 BRIGHT CONT 064 064 Tint adjustment applicable only for NTSC composite or S-Video inputs Only applicable when zoom is over 100 % Horizontal position Adjust horizontal image position. Vertical position Adjust vertical image position. Detail Adjust sharpness of the image. Zoom Allows for 100-200% zoom while the aspect ratio remains unchanged. Pan Move the “zoomed” image horizontally or vertically. Available only when zoom is set over 100%. Horizontal sizing Adjust horizontal image sizing. Vertical sizing Adjust vertical image sizing. Brightness Adjust image brightness. Contrast Adjust image contrast. Color Adjust color of image. Tint Adjust tint of image. Menu System, cont’d A-4 DVS 304 • Menu System Output Configuration menu OUTPUT CONFIG NEXT RESOLUTION 1024x768@60 FORMAT RGBHV H SYNC V NEXT NEXT NEG NEG NEXT PICTURE CONTROL MENU Resolution refresh rate Default: 1024x768 @ 60 Hz Output type • RGBHV (default) • RGBS • RGsB • Y, R-Y, B-Y Sync polarity combinations • H Neg V Neg (default) • H Neg V Pos • H Pos V Neg • H Pos V Pos NOTE This information only appears when the sync polarity is applicable and is based on the selected output format. Audio Configuration menu NEXT IN1 LEVEL 0dB NEXT Input level Adjust the input gain/attenuation from -15dB to +9dB of the selected input. MENU (audio m...
)
