Assessments - , GPA:
(
)
)
Fabricante : Eltax
Arquivo Tamanho: 4.12 mb
Arquivo Nome : c80061f7-0f77-4860-894d-d7c34ffd701a.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
- If the remote control unit is operated near other appliance which generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it may operate incorrectly. -The power is turned on/off (standby) by pressing the POWER button on the remote control unit in standby mode. Precautions concerning batteries -Be sure to insert the batteries with correct positive+ and negative – polarities. - Use batteries of the same type. Never use different types of batteries together. - Rechargeable and non-rechargeable batteries can be used. Refer to the precautions on their labels. - When the remote control unit is not to be used for a long time (more than a month), remove the batteries from the remote control unit to prevent them from leaking. If they leak, wipe away the liquid inside the battery compartment and replace the batteries with new ones. - Do not heat or disassemble batteries and never dispose of old batteries by throwing them in a fire. BATTERY INSTALLATION 1. Remove the battery compartment cover. 2. Insert two “AAA” dry batteries. Make sure that the batteries are inserted with their positive “+” and negative “-” poles positioned correctly. 3. Close the cover until it clicks. If the distance required between the remote control unit and main unit decreases, the batteries are exhausted. In this case, replace the batteries with new ones. 13 REMOTE CONTROL INFORMATION 14 REMOTE CONTROL INFORMATION 1. Power Push this button to turn the unit into standby mode, push it again to turn off the unit. 2. Mute Press this button to mute the sound, push again to cancel the mute function. 3. Input Mode Select Coaxial, Optical or Analog Input mode in DVD, AV1 and AV2. 4. Dimmer Press this button to set the brightness of the front panel display. 5. Display Press this button to display the state of input source. And when listening to the FM broadcasting with RDS, press this button to show PS, PTY, RT and RT. 6. Input Selector buttons 7. Memory Press it to store the broadcast station as a preset. 8. PTY Search In FM state, press this button, the current program type appears on the display, using TUNING +/- to select the program type you desire. 9. Station +/- Press these buttons to select a preset channel during the tuner mode. 10. APS Allocates and memorizes radio stations automatically. (Note: Hold this button down for more than 3 seconds to activate 11. Tuning buttons -Tuning +/-: Tuner frequency up and down. - Band: Press this button to alternate between FM and AM. -Auto/Manual: This button is used to select AUTO or MANUAL tuning for AM and FM stations. Press once to set to AUTO again for MANUAL. - ST/Mono: Press this button to alternate between Stereo and Mono mode when listen to FM broadcast. 12. SUB On/Off Push this button to turn on or off the subwoofer output. 13. Test Tone To balance speakers in Dolby Digital or Dolby Pro Logic mode. 14. CH Select Select channels by pushing this button, then use volume key to balance speakers. 15. Volume +/- Press these buttons to decrease or increase the volume. 16. Bass Press this button for Bass adjustment, then press +/- key to adjust the level. 17. +/- These keys are used for SPK SETUP and DELAY TIME, Treble and Bass adjustment. 18. Treble Press this button for Treble adjustment, then press +/- key to adjust the level. 19. Delay Time Press this button to set the delay time for the Dolby digital/Dolby Pro Logic modes. 20. Bass Mode Press this button to set the delay time for the Dolby digital/Dolby Pro Logic modes. Select one of the two preset speaker configuration according to your speakers. (refer to page 17) 21. Stereo With the unit in the STEREO mode, only front left and front right speakers and Woofer are working. 22. LFE Trim Under the Pro Logic 5.1CH or DTS 5.1CH mode, press this button and adjust the volume to set the Low Frequency output level 23. Surround Mode Select surround modes: MOVIE and MUSIC. 24. Dolby Pro Logic II When receiving Analog/digital PCM signal or 2CH Pro Logic, turn on this button then the playing is under analog 5.1CH state. 25. Dynamic Press this button repeatedly to reach your desired compression dynamic range. 26. DTS/Dolby Digital When playing 5.1CH source, and while you are enjoying Stereo, push this button to playback source in DTS/DOLBY DIGITAL. 15 BASIC OPERATION BASIC OPERATION 1 1. Press the POWER button to put this unit into Standby Mode. 2. Press one of the source buttons to activate the unit. 3. Select the desired source by pressing DVD, VIDEO 1, VIDEO 2, TUNER, AUX or TAPE. If you have selected DVD, VIDEO 1, VIDEO 2 (not TUNER, AUX or TAPE), press INPUT MODE, SURROUND MODE, DTS/DOLBY DIGITAL, STEREO, DOLBY PROLOGIC II or DIGITAL IN in accordance with the type of signal you are receiving and the sound output you require (for example, Dolby Pro Logic II if the DVD movie is an older "classic" and only recorded in stereo). 4. Play the source, and gradually turn up the volume to the required level with the V...