Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Mettez les ergots en face des rainures correspondantes de l’outil. Insert this end into collet Introduzca este extremo en el portaherramienta Enfilez cette extremite dans la douille No shank visible El vastago no debe ser visible La queue ne doit pas etre visible Overthrow Nut Tuerca de sobrerrecorrido Bague filetee (5) (6) (7) Feed Direction Arrow Flecha de sentido de avance Fleche indiquant le sens de l’avance Power Tool Safety Rules ! WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in personal injury. SAVE THESE INSTRUCTIONS Safety Rules for Planer Attachment Keep hands away from cutting area and bit. Keep ! WARNING your second hand on finger grip. If both hands are holding the tool, they cannot be cut by the bit. Hold the tool firmly to prevent loss of control. Figures in this manual illustrate typical hand support of the tool. Advance the planer only in the direction indicated. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. Never hold piece being cut in your hands or across ! DANGER your leg. It is important to support the work properly to minimize body exposure, bit binding, or loss of control. Always use bits that are made specifically for this planer attachment. Do not run tool while carrying it at your side. Accidental contact with the spinning bit could result in serious personal injury. Know how to turn tool switch “OFF” in an emergency. If switch cannot turn “OFF” the tool quickly, unplug the tool immediately. Maintain a firm grip with both hands on the tool and position your body and arm to allow you to resist KICKBACK FORCES. Kickback forces can be controlled by the operator, if proper precautions are taken. When bit is binding, or when interrupting a cut for any reason, turn off the tool and hold the tool motionless in the material until the blade comes to a complete stop. Kickback may occur. Investigate and take corrective action to eliminate the cause of bit binding. Wet lumber, green lumber or pressure treated lumber and most plastics require special attention during planing operation to prevent KICKBACK. Avoid cutting nails. Inspect for and remove all nails from lumber before cutting/planing. Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the surface leading to possible loss of control and serious injury. Do not use dull or damaged bit. Assembly Step One: Removing housing cap from the Rotary Tool Remove collet nut, then remove housing cap from your rotary tool and set housing cap aside. The housing cap must be reinstalled when this attachment is not used (1). Once housing cap has been removed, reassemble collet nut. Disconnect the plug from the power source before ! WARNING making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Step Two: Install Bit In Rotary Tool Remove bit from plastic packaging tube. !WARNING The flutes on the bit are sharp and should be handled with caution. The bit has a long 1/8 inch shank on one end. Insert this end in the collet until the shoulder of the bit bottoms against the collet (2). Depress the shaft lock button and securely tighten the collet nut. No shank should be visible (3). Step Three: Attaching Planer to your Rotary Tool Slide the Planer Attachment over the cutting bit. Align the tip of the cutting bit with the Bronze bushing in the planer end bearing. At the same time, align the two keys with the keyways in the nose of the Rotary Tool (4). When both features are aligned, the planer should slip easily onto the rotary tool. Do not force the planer as this is a sign of misalignment and damage could result. Once installed, slide the Overthrow nut down and rotate until the threads engage with those on the Rotary Tool. Continue to tighten the Overthrow nut until it is tight against the Rotary Tool housing. Hand tighten only. The attachment should be oriented on your Rotary Tool so that the speed control switch in the Tool is easily accessible. Operating Instructions Planing Techniques This planer is designed for two types of planing; straight planing, and 45 degree chamfering. In addition, the straight planing technique can be used for limited shaping/carving. Your rotary tool should be running at the highest speed setting before beginning to plane and turned off after completing the job. Primarily for use on wood or wood-like materials. Other materials may cause blade to wear out prematurely. Not for used on metal or masonry. Holding The Tool A good, firm grip is essential for good control of the planer. One hand should be placed on the rotary tool in the middle or rear of the tool, and with the other hand, grip the finger grip with the thumb and index finger (5). This will provide control and stability. Directional Guide !WARNING N...