Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
2 *T Lockwesher, E.ternaJ 1/4 ................. 2 *U Screw, Pan Hd. 1/4-213 x 1/2 ............... 2 V Jointer-Planer Belt Guard ................. 1 W Attaching Hardware (2 Nuts, 2 Botts) X _lt Guard Clips ........................ 3 Y Belt Guard Support Bracket ............... 1 Z Belt Guard Support ..................... 1 AA Screw Pan Hd. 10-32 x ti2 ................ 2 AB Motor Pulley Belt Guard .................. 1 AC Switch Key ............................ 1 AD Held Dawn/Push Black .................. 2 Yx W VUT unpacking and checking contents TABLE OF LOOSE PARTS The Following Parts Are included With Model 113.206931 Only Item No, Description Qty. A Leg .............................. 4 8 End Stiffener ....................... 2 C Side Stiffener ...................... 4 D Motor Support ..................... 1 E Motor ............................ 1 Package of Miscellaneous Small Parts, No. 67035, Consisting of the Following: F Cord Clip .......................... 2 G Hex Nut, 1/4 in. -20 (approx. die, of hole 1/4 in.) .......... 40 G Hex Nut, 5/I6 in. -18 (approx. alia. of hole 5/1 6 in.) ......... 7 G Hex Nut, 1/2 in. -13 (approx. die. of hole 1/2 in.) .......... 8 H Truss Hd, Screw, !/4 in. -20 x 5/'8 in. long. (Top of screw is rounded) ........ 40 J Flat Washer (dia, of hole 11/32 in.) ...... 7 K Lockwasher, 1/4 in. External Type (approx. dia. of hole 1/4 in.) .......... 40 K Lockwasher, 5/1 6 in. External Type (approx. die. of hole 5/16 in,) ......... 7 L Carriage Boh, 5/16 in. -18 x 3/4 long ... 3 M Leveling Foot ...................... 4 N Hex Hd. Screw, 5/16 in. -18 x 2 in ..... 3 = JL _ , LLUH,H, assembly ASSEMBLING STEEL LEGS NOTE: Steel Legs are furnished with Model 11 3.206931. From among the loose parts, find the following Hardware: 40 Truss Head Screws, 1/4-20 x 5/8 40 Lockwashers, 1/4-External 40 Hex Nuts, 1/4-20 8 Hex Nuts, 1/2q3 4 Leveling Feet 1. Assemble two (2) Side Stiffeners together using four (4) 1/4-20 Truss head screws, Iockwasher and nuts. Make two (2) Side Stiffener assemblies. The End Stiffeners are placed on top and at each end of Side Stiffener assemb)ies as shown. Align holes, letter coded "'B'" in Side Stiffeners and End Stiffeners and then insert 1/4-20 Truss head screws through the 9/32 diameter holes and install Iockwashers and nuts and then tighten. 2. Assemble the four (4) Legs to the Side and End Stiffeners using 1/4-20 screws, Iockwashers and nuts as shown, 3. Assemble the Motor Support to the Legs with 1/4,20 screws, ]ockwashers and nuts. Motor Support can be assembled to either end of Leg set. 4. Install leveling feet as shown. To )eve,] Leg Set, loosen nut on inside of leg and turn nut on the outside to raise or lower feet. Adjust all four leveling feet, if necessary, and then tighten nuts on the inside of leg. NOTE: These levelers are not intended for height adius_ment, C A F JK L M N TRUSS HD. SCREW END STIFFENER 1/4-2i X 51//84EXTERNAL 1 END \ LOCKWASHER _ STIFFENER !_ _//_ 1/4_20 HEX NUT _" IDE STIFFENERS _ JO|NTERfPLANER parts, find the following _HEX HEAD SCREW 18 x3/4 x2 7 Washers; 11/32 ID 7 Hex Jam NUts, 5/16-18 FLATWASHER---ST|FFENER 2 Cord Clips LOCK WAS H ER .-""_::] 2. Loosen FENCE LOCK KNOB. Tilt fence upward and slide HEXNUT J_toward the pulley. 3. Position machine on Leg Set and align mounting holes FENCE LOCK m machine with holes in Leg Set letter coded "'A". KNOB Mount with three (3) 5/16-t8 x 2" Long Hex Head Screws. 1-1t4 IN. SCREW 4. Place a flat washer, a lock washer and a nut on each screw from underneath the stand and tighten. 5. Place handwhee] on shaft aligning flat surfaces on shaft with flat surfaces on handwheel _.. attach with 1-1/4 I In. screw, I I 114-20 TRUSS SIDE STIFFENER I HEAD SCREW / DEPTH OF CUT _DWHEEL o o !B B / ...._o o o °_A END STIFFENER o 0 _ _0 o : : _ Ao -,_ -Q. 7_---_-...... _o_.D --MOTOR SUPPORT AT THIS END 5/32 IN. SETSCREW CHECKING-CUTTER: BLADES AND SCREWS OUTFEED TABLE WRENCH TOOLS NEEDED WEDGE 5/32" and t/8" Setscrew Wrenches (furnished with Jointer). Lead Pencil Short straight edge (or head of combination square) 1. tnsert pencil in space at end of cutterhead to hold cutterhead guard open. BLADE 2. Lower the infeed table with the Depth of Cut Handwheel. 3. Rest the straight edge on edge on the surface of outfeed PENCI L table so it extends across the opening between the CUTTER GUARD tables, at three positions: near each end and at the middle of the cutter blade. 4. Rotate the cutterhead by grasping the 2" alia. driven 5. If a cutter blade adjustment _s not required, check each pulley and make sure each knife nicks (touches) the locking screw of each wedge 15/32" setscrew wrench) straight edge at a ! three post on:s tf not f0 ow and tighten if necessary, Hold the pulley while p ocedure unde REPLAC NG CUTTER BLADES on tightening screws and be careful that your f'ngers do not ppg. 21 and 22. slip off the wrench," i: iNSTALLING SLIDING GUARD PARTS NEEDED I Sliding Guard _ 1 Sliding Guard Knob 1 Sliding Guard Rod 2 Sli...
Este manual também é adequado para os modelos :Planes - 206801 (2.86 mb)
Planes - 113 (2.86 mb)