Assessments - 5, GPA: 3.8
(
)
)
|
Fotos e especificações Makita 1902 |
Facilidade de uso
alternating current FUNCTIONAL DESCRIPTION 002549 1 1. Knob 002553 1 2 1. Lock button 2. Switch trigger ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Removing or installing planer blades CAUTION: • Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. • Handle the blades very carefully. Use gloves or rags to protect your fingers or hands when removing or installing the blades. • Use only the Makita wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury. 002564 1. Remove the existing blade, if the tool has been in use, carefully clean the drum surfaces and the drum cover. To remove the blades on the drum, unscrew the three installation bolts with the socket wrench. The drum cover comes off together with the blades. 2. To install the blades, loosely attach the adjusting plate to the set plate with the pan head screws and set the mini planer blade on the gauge base so that the cutting edge of the blade is perfectly flush with the inside flank of the gauge plate. 002565 3. Set the adjusting plate/set plate on the gauge base so that the planer blade locating lugs on the set plate rest in the mini planer blade groove, then press in the heel of the adjusting plate flush with the back side of the gauge base and tighten the pan head screws. 4. It is important that the blade sits flush with the inside flank of the gauge plate, the planer blade locating lugs 1. Pan head screw sit in the blade groove and the heel of the adjusting plate 2. Adjusting plate is flush with the back side of the gauge base. Check this 3. Planer blade locating lugs alignment carefully to ensure uniform cutting. 4. Gauge plate 5. Heel of adjusting plate 6. Set plate 7. Inside flank of gauge plate 8. Gauge base 9. Back side of gauge base 10.Mini planer blade 002566 5. Slip the heel of the adjusting plate into the groove of the drum. 6. Set the drum cover over the adjusting plate/set plate and screw in the three hex flange head bolts so that a gap 4 exists between the drum and the set plate to slide the mini planer blade into position. The blade will be positioned by the planer blade locating lugs on the set plate. 7. The blade’s lengthwise adjustment will need to be manually positioned so that the blade ends are clear and equidistant from the housing on one side and the metal bracket on the other. 8. Tighten the three hex flange head bolts (with the socket wrench provided) and hand rotate the drum to check 1 2 1. Socket wrench 2. Bolt 1 2 3 4 5 6 7 8 9 10 1 2 3 5 6 1. Mini planer blade 2. Groove 3. Set plate 4. Hex. flange head bolt 5. Drum plate 6. Drum clearances between the blade ends and the tool body. 9. Check the three hex flange head bolts for final tightness. 10. Repeat procedures 1 - 9 for other blade. For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings. EN0004-1 (A) Front base (Movable shoe) (B) Rear base (Stationary shoe) Correct setting Nicks in surface Gouging at start Gouging at end (A) (B) (B) (A) (B) (A) Although this side view cannot show it, the edges of the blades run perfectly parallel to the rear base surface. Cause: One or both blades fails to have edge parallel to rear base line. Cause: One or both blade edges fails to protrude enough in relation to rear base line. Cause: One or both blade edges protrudes too far in relation to rear base line. 1 1. Nozzle assembly 002570 Nozzle assembly (optional accessory) Use of the special nozzle assembly will minimize chip scatter, making for a cleaner work area. 1 2 3 1 2 3 1. Chip cover screw 2. Chip cover 3. Hole 002571 The nozzle assembly may be attached after the chip cover on the tool body is removed. When slipping on the assembly, fit the pin on it into the rear cover hole. Use the chip cover screws to fasten it in place. OPERATION 1 2 1. End 2. Start 002579 Planing ...