Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Turning sprocket (F) clockwise will decrease the distance between the table and head casting. Counterclockwise will increase the distance. 6. Replace chain being careful not to disturb the position of the sprockets and replace idler sprocket assembly (E) Fig. 51. B A Fig. 49 A Fig. 50 C DE Fig. 51 F Fig. 52 20 MACHINE USE When using your machine, you may want to follow these few simple steps for achieving the best results possible. 1. True Up One Face – Feed one face of the board over a jointer, making thin cuts with each pass, until the entire surface is flat. 2. Plane to Thickness – Place the side you just surfaced in STEP 1 face down and feed the board through the planer, plane until this side is flat. Then plane both sides of the board until you are satisfied with the thickness, making thin cuts, alternating sides with each pass. If during the planing operation you notice the board twisting, warping or bowing, repeat STEP 1 and true up one face. 3. When planing long stock, provide table extensions to support the infeed and outfeed end of the workpiece. 4. For best results, always engage cutterhead lock before planing, plane with the grain only, and keep planer table clean. Occasionally, wax table surface to reduce friction during the planing operation. 5. Cross-cut to Final Length – Cross-cut lumber to final length. THE KNIVES ON THE PLANER WILL NOT WEAR EVENLY BY FEEDING THE WOOD THROUGH THE SAME SPOT ON THE TABLE EVERY TIME. FEED THE WOOD THROUGH THE PLANER AT DIFFERENT SPOTS ON THE TABLE WHEN POSSIBLE, TO HELP ELIMINATE UNEVEN WEAR OF THE KNIVES. TROUBLESHOOTING For assistance with your machine, visit our website at for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). 21 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. FAILURE TO START Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. PROTECTING CAST IRON FROM RUST To clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a jointer, 1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40®, 1 can of degreaser, 1 can of TopCote® Aerosol. Apply the WD-40 and polish the table surface with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the TopCote® accordingly. LUBRICATION The gear box oil should be changed once a year. Use extreme pressure gear oil, available from Delta in one pint cans (you will need approximately 20 oz.). The gear box drain plug is shown at (A) Fig. 53. The oil fill and level plug is shown at (B) Fig. 54. Fig. 55 A Fig. 53 B Fig. 54 E C D The four raising screws, two of which are shown at (C) Fig. 55, should be lubricated as required using a common grease. Periodically remove screw (D) Fig. 55, and side cover (E). Thoroughly clean chains and sprockets (F) Fig. 56, and lubricate using a light (10W) machine oil. Replace side cover (E) Fig. 55, and secure with screw (D). Periodically squirt light (10W) machine oil on the feed roller bushings (G) Fig. 57, two of which are shown, at each end of the feed rollers. F Fig. 56 CLEANING INFEED AND OUTFEED ROLLERS The infeed and outfeed rollers (H) Fig. 57, will need to be cleaned periodically. Use soap and water and scrub the infeed and outfeed rollers with a scotch brite pad. G H Fig. 57 22 SERVICE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582). ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product. WARRANTY Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns ...