Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
This information relates to protecting personal safety and preventing equipment problems. It is the responsibility of the owner/operator to inform anyone operating or working in the area of this equipment of these safety guidlines.To help you recognize this information, we use the symbols that are defined below. Please read the manual and pay attention to these sections. Failure to read this manual and it’s safety instructions is a misuse of the equipment and may lead to serious injury or death. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. NOTE indicates information about the equipment that you should pay special attention to. Bin Level 1. Disconnect all power before servicing or adjusting. Have bin properly grounded. NOTE: With power on, the unit will start unexpectedly if the mercury switch is activated by jerking, shaking or jarring. 2. Do not enter a bin without proper eye protection while the unit is operating. 3. Do not attempt to service or adjust the unit from a ladder unless the ladder is secured to another piece of equipment or to the bin. The grain spreader can swing and will not support a ladder. Be sure electric power IS DISCONNECTED. 4. Power cords, plug and receptacles should be grounded type to prevent personal injury. 5. All wiring should be done according to the National Electric Code and by a qualified electrician. 6. Read and understand the operator’s manual. ****WARNING**** FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. INSTALLATION FIG. 1 FIG. 5 FIG. 2 FIG. 3 FIG. 4 Bin Level Installation and Operation INSTALLATION Figure 1: 918 and 936 Bin Level - Hanger Hooks and Chains Double chains are attached to the hopper in three places. One chain from each of the three attachment points is hooked into a hanger hook to form a “V”. This is necessary to keep the spreader from swinging around the fill- hole each time the spreader is started. The Bin Level hanging height can change the spreading pattern. On steep-roofed bins, hanging the Bin Level lower in the bin will be beneficial for a more level grain spread. All Bin Levels should be installed so that, during operation, grain from legs or augers is not directly hitting the mercury switch control plate. INSTALL THE BIN LEVEL SPREADER AS LEVEL AS POSSIBLE ADJUSTMENT & OPERATION Figure 2: Adjusting Flow Rate The two wing nuts inside of the top of the hopper regulate the volume of grain the Bin Level will spread by adjusting the gap between the lower end of the hopper and the spreader pan. This adjustment should be made so the incoming grain operates the switch, turning the motor on at least three times per minute and not more than six times per minute. If the Bin Level is adjusted to start and stop less than three times per minute, level spread cannot be achieved. If adjusted to start and stop more than six times per minute, motor damage can result. Adjusting the Bin Level to operate within the recommended “stop” and “start” pattern is a must to achieve a level spread. Figure 3: Outside Ring Adjustment The outside ring of the Bin Level grain spreader is designed so it can be raised or lowered depending upon the amount of grain being put through the spreader and the width of spread needed. Because of this feature the grain is showered up and out into the bin which allows an even spread, regardless of the corn depth in the bin. To attain this showering action, the outside ring has to be kept higher than the bottom of the hopper cone. Under normal conditions, the outside ring should be from 1/2” to 3/4” higher than the bottom of the Bin Level cone or fill hopper. Raise the ring to throw grain farther to the outside. Lower the ring to decrease spread width. Figure 4: Side Gate Adjustments A slide gate is provided in the spreader pan to keep the center level with the remainder of the bin. Adjustment of the slide gate will vary, depending upon volume and number of start-stops per minute at which the Bin Level is set. CHECK PERIODICALLY FOR CLOGGING WITH TRASH Figure 5: Mercury Switch Control This is the heart of the Bin Level grain spreader. By use of the mercury switch, the spreader is always operating under full-load capacity so a very even spread is obtained. IMPORTANT: For proper operation, the mercury switch plate has to be kept from becoming bent or from having other physical damage, and must work ...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 918 (202.34 kb)