Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Bystanders should be encouraged to wear eye protection. If you are approached, stop the unit immediately. • Only for use on attachment-capable, gas-powered trimmers that have the On/Off Stop control located on the grip. On/Off Stop Control (located on grip) RULES FOR SAFE OPERATION • The TBBC is specifically approved for use with the following models of attachment-capable trimmers: Ryobi: Troy-Bilt: 775R TB20CS 750R TB25CS 790R TB25ET 890R TB70SS TB75SS Yard Man: TB90BC YM25 TB425CS YM75 TB475SS YM90 TB490BC YM26BC Bolens (Canada): Cub Cadet: BL26BC CC2025 CC3075 Yardworks: CC4025 60-2310-6 CC4075 60-2311-4 CC4090 60-2312-2 SAFETY WARNINGS FOR GAS POWERHEADS Gasoline is highly WARNING: flammable, and its vapors can explode if ignited. Take the following precautions: • Store fuel only in containers specifically designed and approved for the storage of such materials. • Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressure in the tank. • Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Slowly remove the fuel cap only after stopping engine. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately. • Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate. • Move the unit at least 30 feet (9.1 m) from the fueling source and site before starting the engine. Do not smoke. Keep sparks and open flames away from the area while adding fuel or operating the unit. • Squeeze the throttle control and check that it returns automatically to the idle position. Make all adjustments or repairs before using the unit. • Do not touch the engine, gear housing or muffler. These parts get extremely hot from operation, even after the unit is turned off. • To reduce fire hazard, replace a faulty muffler and spark arrestor. Keep the engine and muffler free from grass, leaves, excessive grease or carbon build up. • Never start or run the unit inside a closed room or building. Breathing exhaust fumes can be fatal. Operate this unit only in a well-ventilated outdoor area. WHILE OPERATING • Read and understand all safety warnings before operating this unit. • Inspect thoroughly for loose nuts, bolts or damage before continuing. Repair or replace affected parts as necessary. • Wear safety glasses or goggles that meet ANSI Z87.1 standards and are marked as such. Wear ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty. • Wear heavy long pants, boots, gloves and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level. • Adjust the J-handle to your size in order to provide the best grip. • Use the unit only in daylight or good artificial light. • Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. Refer to Starting/Stopping Instructions of the power head manual. • Use the right tool. Only use this tool for its intended purpose. • Do not overreach. Always keep proper footing and balance. • Always hold the unit with both hands when operating. Keep a firm grip on both handles or grips. • Keep hands, face, and feet at a distance from all moving parts. • Do not operate the engine/motor faster than the speed needed to cut. Do not run the engine at high speed when not cutting. • Always stop the engine when you delay working, or when you walk from one cutting location to another. • If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Do not operate before repairing damage. Do not operate the unit with loose or damaged parts. RULES FOR SAFE OPERATION • Stop the unit, switch the engine to off, and disconnect the spark plug for maintenance or repair. • Use only original equipment manufacturer replacement parts and accessories for this unit. These are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to serious injury to the user, or damage to the unit, and void your warranty. • Keep unit clean of vegetation and other materials. • Always use the shoulder harness when using the brush blade attachment. • Keep the J-handle between the operator and blade at all times. • NEVER cut when the cutting blade is 30 inches (76 cm) or more above the ground level. • Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut. Blade thrust can be violent enough to propel the unit and/or operator in any direction, possibly causing a loss of control. Blade thrust can occur without warning if the blade snags, stalls or binds. This is more likely to occur in areas where it is...