Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
Only use the recommended cutting attachment. See the chapter on Technical data. • Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared. • The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.This will make the line tougher so that it lasts longer. 10 – English ASSEMBLY Fitting the loop handle (GT 2125) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (GC 2125, GC 2125C) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, washer and screw. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Fitting the J-handle (GC 2125, GC 2125C) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Attach the J-handle to the loop handle using the three screws, as shown. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. ! WARNING! Only grass blades/grass cutters or trimmer heads/plastic blades may be used when the J-handle is fitted. Saw blades must never be used with the J-handle. English – 11 12 – English ASSEMBLY Assembling and dismantling the two-piece shaft (GC 2125C) Assembly: • Loosen the coupling by turning the knob. • Align the tab of the attachment (A) with the arrow on the coupling (B). • Push the attachment into the coupling until the attachment snaps into place. • Before using the unit, tighten the knob securely. Dismantling: • Loosen the coupling by turning the knob (at least 3 times). • Push and hold the button (C). While securely holding the engine end, pull the attachment straight out of the coupling. Assembling the cutting equipment Fitting the trimmer guard and Auto 32 trimmer head (GC 2125, GC 2125C) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows: A B C ! WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. ! WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury. IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness. G F I A B C K J I L K English – 13 ASSEMBLY • Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Pull apart the trimmer head, grasping the cover firmly. • Place the cover (I) and the support flange (F) on the output shaft. • Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. • To dismantle, follow the instructions in the reverse order. Fitting the blade guard/combination guard, grass blade and grass cutter (GC 2125, GC 2125C) • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Inse...
Este manual também é adequado para os modelos :Ferramentas para Jardim - GC 2125C (1.29 mb)