Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
770-4235 LIMITE:.D WARRANTY For one year from the date of original retail purchase, MTD PRODUCTS INC will either repair or replace, at its option, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. Transportation charges for the movement of any power equipnent unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by MTD PRODUCTS INC. This warranty will not apply to any part which has become inoperative due to misuse, excessive use, accident, neglect, improper maintenance, alterations, or unless the unit has been operated and maintained in a ;cordance with the instructions furnished. This warranty does not apply to the engine, motor, battery, battery chargeror component parts thereof. Please refer to the applicable manufacturer’s warranty on these items. This warranty will not apply where the unit has been used commercially. Warranty service is available throu jh your local authorized service dealer or distributor. If you do not know the dealer or distri outor in yourarea, please write to the Customer Service Department of MTD. The return of a complete unit will r ot be accepted by the factory unless prior written permission has been extended by MTD. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. FIGURE 1 R U ASSEMBLY INSTRUCTIONS NOTE Right and left hand side of the unit is determined from the driver's seat, facing forward. -Contents of Hardware Pack (See figure 1): A (1) Extension Spring В (1) Flat Washer 1/2" I.D. x 1-1/2" O.D. С (1) Flat Washer 5/8" I.D. x 1-1/4" O.D. D (2) Flat Washers 1/2" I.D. x 1" O.D. E (4) Hex Bolts 3/8-24 x 7/8" Long F (4) Lock Washers 3/8" I.D. G (4) Hex Nuts 3/8-24 Thread H (1) Hex Bolt 5/16-24 x 1" Long I (1) Spirol Pin J (5) Hairpin Cotters M (1) Hex Bolt 5/16-24 x 1-1/2" Long N (2) Lock Washers 5/16" l:D. 0 (3) Hex Nuts 5/16-24 Thread P (1) Ferrule Q (1) Spacer 1/2" I.D. x 1” O.D. x 1/2" Long Loose Parts in Carton (See figure 2): R (1) Carriage Bracket Assembly S (1) Idler Bracket Support Arm Assembly T (2) Support Pivot Brackets U (1) Compression Spring V (1) Idler Bracket Assembly W(1) Lift Rod Assembly FIGURE 2 BRACKET (T) FIGURE 3 1. Remove the cutting deck from your tractor if one is attached. 2. Preassemble the idler bracket support arm (S) to one support pivot bracket (T) and idler bracket assembly as follows. A. Place the idler bracket support arm through the hole in support pivot bracket as shown in figures 3 and 4. 3 I ASSEMBLY (V) FIGURE 4 FIGURE 5 HEX BOLT (E) FIGURE 6 B. Next, slide the idler bracket assembly (V) over the idler bracket support arm. Secure with spirol pin (I). See figure 4. 3. Remove the two hairpin cotters on the rear of your tractor. See figure 5. These will be reassembled to your unit in steps 4 and 9. 4. Place the support pivot bracket (with idler bracket and support arm attached) in position on the rear left hand side of tractor. Place large hole in pivot bracket over shaft on tractor. Secure with one hairpin cotter removed in step 3. 5. Thread one hex nut (O) all the way onto hex bolt (M) (1-1/2" long). 6. Place the support pivot bracket in position so the forward hole (larger) in the bracket aligns with the larger hole in the tractor frame. 7. Secure the support pivot bracket to the tractor by placing hex bolt (M) (with nut assembled) in the smaller hole in plate which aligns with hole on tractor. Start hex nut (0) and lock washer (N) by hand. See figure 6. 8. Place one hex bolt (E) through top forward hole in bracket and tractor frame. Secure with lock washer (F) and hex nut (G). 9. Assemble the other support pivot bracket to the right hand side of tractor in the same manner, except use hex bolt (И) (1" long) instead of the longer hex bolt and the extra hex nut. 10. Tighten securely all four nuts and bolts which were used in assembly of pivot support brackets. 11. Secure end of idler bracket support arm assembly on the right side of tractor with one flat washer (D) and hairpin cotter (J). 4 CARRIAGE BRACKET ASSEMBLY (R) 12. Place carriage bracket assembly (R) in position beneath the running board support rod on the tractor. Secure each side of carriage bracket to frame with hex bolts (E), lock washers (F) and hex nuts (G). Tighten securely. See figure 7. FIGURE 7 ROUND BELT GUARD 13. Remove the round belt guard from the idler on tractor by removing the hairpin cotter. See figure - 8. FIGURE 8 14. Unscrew the "L" bolt and swing the wire belt guard on the engine pulley forward. See figure 9. FIGURE 9 5 L'BOLT VfIRE EELT CUARD GUARD 11 HAIRPIN COTTER FIGURE 10 IDLER PULLEY 15. Place the belt which is preassembled to the carriage bracket assembly around the idler pulley and engine p...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 19746S (1.32 mb)