Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Run the engine until it stops from lack of fuel. The small amount of fuel that remains in the sump of the tank should then be removed by absorbing it with a clean dry cloth. (b) Clean dirt and chaff from cylinder, cylinder head fins and blower housing. (c) Remove spark plug, pour 2 or 3 tablespoons of SAE-30 oil into cylinder and pull crank cord out slowly to distribute oil. Replace spark plug. Just as your automobile needs professional mechanical maintenance from time to time, so does your air-cooled engine. Cleaning and adjusting of the carburetor and periodic replacement of the spark plug and ignition points is made necessary by NORMAL use. Professional Air-Cooled Engine Service is as close as your telephone book. A yearly checkup or tune-up by an authorized engine dealer is a good idea to avoid breakdowns or delay.. .do it at the end of the season, then you’re ready for the next. TILLER WINTERIZING INSTRUCTIONS FOR USE WITH SNOW BLADE: 1. For cold weather (below 32°F.), drain oil from tiller engine crankcase and replace with SAE 10W or 10W-20 detergent oil. 2. Replace any remaining fuel on hand or in the engine fuel tank with a fresh supply of winter grade fuel. Winter fuels contain additives for faster starts. Keep fuel tank full. NOTE It may be necessary to enrich the carburetor idle and high speed jets 1/8 to 1/4 turn (counterclockwise) for good performance. 3. In the spring of the year, before the tilling season, be sure to change engine oil back to SAE 30W detergent oil. 13 I Model 381 IF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL Model 381 **\ PARTS LIST FOR MODEL 381 TILLER 3EF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 710-0160 Hex Wash Hd. AB Tap Scr. 27 712-0267 Hex Nut 5/16-18 Thd.* #8 x .62" Lg. 28 736-0119 L-Wash. 5/16" I.D.* 2 15278 —463 Handle Panel Ass’y. 29 736-0921 L-Wash. 1/2" I.D.* 3 720-0180 Handle Grip 30 712-0200 Hex Inst. L-Nut y2-20 Thd. 4 731-0108 Throttle Control Knob 31 06813 —463 Wheel Bracket Ass’y. 5 714-0149 Internal Cotter Pin 32 06792 Engine “U”-Channel 6 04602 “U”-Clevis Pin .500" Dia. Ass’y.—L.H. 7 710-0451 Carriage Bolt 5/16-18 x .75" 33 712-0267 Hex Nut 5/16-18 Thd.* Lg.* 34 710-0322 Hex Sems Bolt 5/16-18 x 8 04586 “U”-Channel Plate 1.00" Lg.* 9 711-0231 Clevis Pin .500" Dia. 35 06794 Engine “U”-Channel 10 04668 -463 Depth Bar Ass’y.—R.H. 11 732-0194 Spring Pin 36 749-0356 Handle—R.H. 12 732-0290 Depth Bar Spring 37 711-0599 Clevis Pin 13 736-0119 L-Wash. 5/16" I.D.* 38 736-0119 L-Wash. 5/16" I.D.* 14 714-0145 Internal Cotter Pin 39 712-0267 Hex Nut 5/16-18 Thd.* 15 736-0119 L-Wash. 5/16" I.D.* 40 06816 “U”-Channel Bracket Ass’y. 16 712-0267 Hex Nut 5/16-18 Thd.* 41 712-0267 Hex Nut 5/16-18 Thd.* 17 749-0502 Handle—L.H. 42 04589 Tailpiece Ass’y. 18 710-0253 Hex Bolt 3/8-16 x 1.00" Lg.* 43 747-0183 Control Rod 19 736-0105 Belleville Wash. 3/8" I.D. 44 747-0182 Clutch Lever 20 710-0118 Hex Bolt 5/16-18 x .75" Lg.* 45 720-0143 Grip 21 736-0169 L-Wash. 3/8" I.D.* 46 746-0369 Throttle Control Ass’y. 22 712-0798 Hex Nut 3/8-16 Thd.* Comp. 23 736-0253 Belleville Wash. .505 I.D. x 47 735-0126 Rubber Wash. 1.00" O.D. 48 736-0159 FI-Wash. .344" I.D. x v 24 710-0458 Carriage Bolt 5/16-18 x 1.75" .880 O.D. x .06 Lg.* 49 712-0158 Hex Cent. L-Nut 5/16-18 Thd. 25 734-0968 Wheel Ass’y- 9 x 1.75 50 732-0191 Extension Spring .75" O.D. 26 738-0318 Shoulder Bolt .625" Dia. x x 11.0" Lg. 2.75" Lg. 'For faster service obtain standard nuts, bolts, and washers locally. If these items cannot be obtained locally, order by part number and size as shown on parts list. (463—Top Flite Red) When ordering parts if color or finish is important, use the appropriate color (447—Patina Silver) code shown at left. (e.g. Top Flite Red Finish—15278 (463).) The engine is not under warranty by the tiller manufacturer. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines—Gasoline.” Find It Fast In The Yellow Pages This instruction manual covers various models and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 15 I Model 381 Part No. 15376 15378 15375 15377 TINE CHART Description Inner Tine Ass’y. Comp.—R.H. OuterTine Ass’y- Comp.—R.H. Inner Tine Ass’y. Comp.—L.H. OuterTine Ass’y. Comp.—L.H. 16 v Model 381 *\ PARTS LIST FOR MODEL 381 TILLER REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 — Engine 27 756-0261 Engine Pulley 2 712-0287 Hex Nut 1/4-20 Thd.* 28 736-0258 FI-Wash. 3/8" I.D. x 1.00" 3 736-0329 L-Wash. 1/4" ...