Assessments - 6, GPA: 4.3
(
)
)
|
Facilidade de uso
Loosen lower jam nut. Turn nut down cable in 1/8” increments. 2. Tighten upper jam nut. 3. Check adjustment. This procedure can be repeated until conduit adjustment bolts are fully adjusted. If no more adjustment can be made, belt may have to be replaced. Forward Cable Upper Jam Nut Lower Jam Nut Figure 14 Tilling Tips J The key to successful tilling is to begin with a shallow cut on the first pass, and then work an inch or two deeper on each successive pass. • Tilling depth will vary with ground conditions. • When beginning to till in unbroken ground or in extremely hard soil, set the detent pin in the highest hole of the depth regulator lever (follow instructions under Tilling section). This will allow for shallow tilling. With the drag stake in this position, make several light passes over the area to be tilled. Reset for deeper depths with successive passes. • If tiller jumps or skids uncontrollably, lower the drag stake by placing the detent pin in a higher hole. This will allow for shallower tilling. Hold firmly to the handlebars to control sudden lurches. • If weeds, tall grasses, vines, or other materials clog or jam the tines, reverse the tiller to unwind vegetation. WARNING Immediately release the drive control levers if the tines jam or you strike a foreign object. With drive control levers in neutral position, stop the engine. Disengage the spark plug wire. When tines have stopped, remove foreign objects and check for damage. WARNING EXTREME CAUTION MUST BE TAKEN IN SELECTING TILLING DEPTH. IF YOU ATTEMPT TO TILL TOO DEEPLY FOR SOIL CONDITIONS, THAT IS, WITH THE DEPTH REGULATOR LEVER IN TOO HIGH A POSITION, LOSS OF CONTROL COULD RESULT. IF REMOVING MATERIAL FROM THE TINES bY HAND, STOP ENGINE AND REMOVE SPARK PLUG WIRE FIRST. Cultivating Tips K If you plan to use your tiller for cultivating: • Plant rows on 20" - 22" centers for ease of turning. • Set the depth regulator lever with the detent pin in one of the higher holes. This will allow for shallow cultivation necessary to turn over weeds, and break up and aerate the soil. Questions? Call Toll Free at 1-800-737-2112 14 Copyright © 2009 MAT Engine Technologies, LLC Maintenance • Save all instructions Maintenance Schedule A WARNING Before performing any maintenance, turn engine off and remove the wire from the spark plug to prevent accidental starting and serious injury. IMPORTANT: The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the tiller as instructed in this manual, and only use genuine replacement parts. The following table lists required periodic maintenance. PERIODIC MAINTENANCE SCHEDULE TABLE Service Records- Fill in dates as you complete regular service Before Each Use After Every 10 Hours of Use After Every 25 Hours of Use After Every 50 Hours of Use After Every 100 Hour of Use Before Each Season Before Storage See Note Below Check Engine Oil Level, Fill to Proper Level v v Check Connection of bOTH Flameout Wire Connectors v v Clean Debris From Unit v v v Lubricate All Pivot Points v v v Check Fasteners for Tightness v v 1 Check Drive Belts Replace if Necessary v v Check Tines for Wear or DamageReplace if Necessary v v Check Fuel Line Replace if Necessary v v Lubricate Wheel Axles v v v Check Spark PlugReplace if Necessary v v Change Engine Oil v v v 2,3 Clean Air Filter Replace if Necessary v v 4 Replace Spark Plug v Clean Combustion Deposits fromCylinder, Piston, and Valves v CAUTION IMPORTANT NOTES about Maintenance schedule 1. Re-check tightness of all fasteners after first 2 hours of initial use 2. Change engine oil after first 5-8 hours of initial use 3. Change oil every 25 hours if operating under heavy load or in high temperatures 4. Clean air filter every 10 hours if operating under dusty conditions. WARNING Use only GENUINE replacement parts. Other parts may damage the unit or result in injury. Questions? Call Toll Free at 1-800-737-2112 15 Copyright © 2009 MAT Engine Technologies, LLC Maintenance (Continued) • Save all instructions Servicing the Tiller B WARNING wireThe following information will help you make the necessary checks and perform the procedures required to follow the normal care recommendations made for your tiller unit. If you prefer, your local authorized dealer can make these checks and perform the required procedures for you. tab TO PREVENT ACCIDENTAL STARTING: ENGINE MUST BE TURNED OFF AND COOL, AND SPARK PLUG WIRE MUST BE REMOVED AND SECURED FROM SPARk PLUG bEFORE CHECkING AND ADJUSTING ENGINE OR EQUIPMENT. CHANGE BELTS (See Figure 14) 1. Turn off engine. Engine must be cool completely before proceeding. 2. Remove spark plug wire and secure from spark plug. 3. Reduce the belt tension by loosening the cable upper jam nut. 4. Remove the front carry handle, front and rear belt cover. • remove the belt from the forward engine pulley: -loosen the three engine mounting bolts -slide the b...
Este manual também é adequado para os modelos :Ferramentas para Jardim - P-FTT-160MD-[E] (1.13 mb)