Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
The approximate broadcast widths for different materials are shown in the application chart on this page. 10. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. 11. Heavy moisture conditions may require a cover over the hopper to keep contents dry. The vinyl cover (available as an accessory) acts as a wind and moisture shield, but should not be used as a rain cover. Refer to the parts list on page 11. IMPORTANT: Application rates shown in the chart are affected by humidity and by the moisture content of the material (granular and pellet). Some minor setting adjustments may be necessary to compensate for this condition. APPLICATION CHART MATERIAL TYPE FLOW SETTING SPREAD WIDTH FERTILIZER Powder 3 - 5 3' - 4' Granular 3 - 5 8' - 10' Pelleted 3 - 5 10' - 12' Organic 6 - 8 6' - 8' GRASS SEED Fine 3 - 4 6' - 7' Coarse 4 - 5 8' - 9' ICE MELTER 6 - 8 10' - 12' OPERATING SPEED - 3 MPH. (100 ft. in 23 seconds) MAINTENANCE SERVICE AND ADJUSTMENTS REPLACING SLOTTED GEAR 1. If the axle, slotted gear and sprocket assembly is disassembled, mark down the positions of the parts as they are removed. The drive wheel and sprocket positions in relation to the slotted gear determine which direction the spreader plate will spin. Be sure to reassemble them in their original positions. (Refer to figure 3 on page 4.) Use shim washers (Ref. no. 21 on pages 10 and 11) as needed for minimum backlash. Add grease to gear and sprocket. CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. CHECK FOR WORN OF DAMAGED PARTS 2. Check for worn or damaged parts before each use. Repair or replace parts if necessary. CHECK TIRE INFLATION 3. Check if tires are adequately inflated before each use. Do not inflate tires beyond maximum recommended pressure. CLEANING 4. Rinse inside of hopper and exterior of spreader and dry off before storing. LUBRICATE (See figure 15) 5. Lightly apply automotive grease as needed to the sprocket and gear. 6. Oil the nylon bushings on the vertical sprocket shaft and on the axle at least once a year, or more often as needed. 7. Oil right hand (idler) wheel at least once a year or more often as needed. LOCKED UP SPREADER 1. Turn the spreader over so that the wheels are off the ground. 2. Loosen all three nuts on the shaft support plate just enough so that the bolts can be turned easily with a wrench but cannot be turned by hand. 3. Spin the drive wheel and note how freely it spins and how much noise the slotted gear makes. 4. To free up the wheel and gear, tap gently on the front or rear edge of the shaft support plate to move it slightly forward or backward. You can also tap at the corners of the plate to angle it slightly. 5. Spin the drive wheel after each adjustment to see if it spins more freely and if the gear noise is reduced. 6. Continue making slight adjustments until you find the position where the drive wheel spins most freely and the gear makes the least noise. 7. Secure the shaft support plate in this position by retightening all three nuts that you loosened. CAUTION: DO NOT inflate tires beyond the maximum recommended pressure printed on side of tire. SHAFT SUPPORT PLATESLOTTED GEAR GREASEOILOIL FIGURE 15 FIGURE 16 STORAGE 1. Rinse inside of hopper and exterior of spreader and dry off before storing. 2. Store in a clean, dry area. REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02104 14222235613461011181819202033253826363149173535BADED16142748373743 4434414281111453950502323151521282829324040999999999 77777792921213221AB243294E93039514093939CC403247522921 REPAIR PARTS LIST FOR BROADCAST SPREADER MODEL 45-02104 REF. NO. PART NO. QTY. DESCRIPTION 1 44466 1 Hopper 2 C-9M5732 2 Pop Rivet (not shown) 3 62482 1 Ass'y, Guide Closure 4 48842 1 Tube, Frame 5 23753 1 Slide Gate Angle Bracket 6 23758 1 Slide Gate Bracket 7 43648 9 Bolt, Hex 1/4-20 x 1-1/2" Lg.* 8 24857 1 Flow Control Link 9 47189 22 Nut, Nyock 1/4-20 Thd. * 10 48841 1 Tube, Crossover 11 43661 3 Bolt, Hex 1/4-20 x 1" Lg.* 13 44566 1 Spring, Torsion 14 44590 1 Tube, Handle (Long) 15 40880 2 Wheel 16 44589 1 Tube, Handle (Short) 17 25067 1 Shaft, Axle 18 44665 2 Pin, Spring 5/32" Dia. x 1-1/4" Lg. 19 48916 1 Bushing, Axle Shaft 20 44125 4 Washer, Shim 5/8" I.D. 21 R19212016 5 Washer, Flat 5/8" I.D. 22 741-0249 2 Bearing, Flange 23 48857 2 Tube, Spacer 24 25305 1 Shaft, Sprocket 25 04367 1 Spreader Plate 26 43850 1 Pin, Spring 1/8" Dia. x 5/8" Lg. 27 44587 1 Tube, Leg Stand REF. NO. PART NO. QTY. DESCRIPTION 28 44285 2 Bushing, Delrin 3/8" I.D. 29 1509-69 9 Bolt, Hex 1/4-20 x 1-3/4" Lg.* 30 47063 1 Pin, Cotter 5/32" x 2" 31 48934 1 Hairpin, Agitator 32 43088 16 Washer, Flat 1/4" Std. 33 44468 1 Sprocket - 6 Tooth 34 44514 1 Rod, Flow Control 35 23525 2 Brace, Hitch 36 23780 1 Support, Shaft 37 44482 2 Grip, Handle 38 46055 1 Pin, Spring 1/8" Dia. x 1" Lg. 39 1543-69 1...