Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Assemble the Hitch Brackets to the Hitch Control Tube using two 1/4" x 1-1/4" hex bolts and 1/4" nuts. Tighten. See figure 3. 5. Assemble the hitch pin through the hitch brackets and secure with the 1/8" hair cotter pin. See figure 3. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on page 3. 1/4" NUT1/4" x 1-1/4" HEX BOLTHAIR COTTER PINHITCH PIN 1. Assemble vinyl caps onto the ends of the R.H. and L.H. Hitch Tubes. See figure 1. 2. Assemble the R.H. Hitch Tube to the spreader frame tube using two 1/4" x 1-3/4" hex bolts and 1/4" nuts. Do not tighten yet. Repeat for L.H. Hitch Tube. See figure 1. 1/4" x 1-3/4" HEX BOLT1/4" NUT VINYL CAP FIGURE 3 6. Assemble the vinyl cap onto the Hitch Control Tube. See figure 4. 7. Assemble the Control Cable to the Hitch Control Tube using the carriage bolt and nylon wing nut. See figure 4. FIGURE 1 3. Assemble the Hitch Control Tube between the Hitch Tubes using two 1/4" x 1-1/4" hex bolts and 1/4" nuts. Tighten all bolts and nuts . See figure 2. CARRIAGE BOLTNYLONWING NUTVINYL CAP 1/4" NUT1/4" x 1-1/4" HEX BOLT FIGURE 4 FIGURE 2 OPERATION APPLICATION TIPS 1. This unit will cover a 4 to 8 foot wide area depending on the material used and the towing speed. 2. To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. 3. For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips. See figure 6. 4. If lawn is odd shaped, spread a border around the edges and then spread between the border. See figure 6. 5. Keep wheel approximately 4 feet from any area you do not wish to spread. IMPORTANT: Be careful when using spreader around ornamental plants because weed control chemicals can damage these plants. HOW TO USE YOUR SPREADER ADJUSTING THE FLOW RATE SETTING 1. Loosen the wing nut that fastens the control to the handle. 2. Slide the Adjustable stop to the desired setting and retighten the wing nut. See figure 5. FLOW CONTROL LEVERADJUSTABLE STOP FIGURE 6 FIGURE 5 MAINTENANCE & STORAGE USING YOUR SPREADER 1. Check the material package and the Spreader Settings sheet included with your spreader for the proper spreader setting and application rate. 2. Before filling spreader, move the control lever to the "OFF" position. 3. Move spreader onto a flat surface - either a walk or a driveway - and fill. 4. Slide the Adjustable Stop to the desired setting. 5. Start the spreader in motion, then move the control lever forward against the adjustable stop to begin spreading. 6. Maximum towing speed - 3 M.P.H. NOTE: Always place control lever in the "OFF" position while filling spreader and when stopping or turning, to prevent release of excess fertilizer. CHECK FOR LOOSE FASTENERS 1. Make a thorough visual check of the Spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. LUBRICATION 1. Apply a few drops of oil to all moving parts. CLEANING 1. Always empty spreader after each use, storing leftover material in it's original bag. 2. Wash the spreader and dry thoroughly after each use. STORAGE 1. Empty and clean the hopper as instructed in maintenance section. 2. Store in a clean, dry area. REPAIR PARTS FOR MODEL 45-0410 127926227435121414161618192021222225292383087246868131011728152517 REF. PART QTY. DESCRIPTION NO. NO. REF. PART QTY. DESCRIPTION NO. NO. 1 49490 1 Hopper 2 40513 1 Frame Tube 3 40515 1 Hitch Tube (LH) 4 40514 1 Hitch Tube (RH) 5 40516 1 Hitch Control Tube 6 1509-90 4 Hex Bolt, 1/4-20 x 1-1/4" 7 1509-69 4 Hex Bolt, 1/4-20 x 1-3/4" 8 46978 10 SEMS Nut, 1/4-20 9 43648 2 Hex Bolt, 1/4-20 x 1-1/2" 10 45165 1 Carriage Bolt 1/4-20 x 2" 11 47141 1 Nylon Wing Nut 1/4-20 12 47983 1 Flow Slide 13 49820 1 Control Cable Asembly (includes items 10 & 11) 14 40511 2 Wheel 15 44486 2 Hex Head Screw, #12 x 3/4" 16 44663 2 Hub Cap (Push Nut) 17 48003 1 Axle 18 47851 2 Spacer 19 49084 1 Gearbox 20 47124 1 Impeller 21 47963 2 Hex Flange Bearing 22 40518 2 Hitch Bracket 23 47623 1 Hitch Pin 24 49489 1 Control Bracket 25 44481 3 Vinyl Cap 26 R19111116 2 Washer 27 47134 3 Hairpin, Cotter 28 47113 2 Washer 29 43343 1 Hairpin, Cotter 30 R19171616 2 Washer 40438 1 Owners Manual thefastest way to purchase parts NOTES thefastest way to purchase parts www.speed...