Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Assemble the Hitch Brackets to the Hitch Control Tube using two 1/4" x 1-3/4" hex bolts and 1/4" hex nuts. Tighten. See figure 3. 5. Assemble the hitch pin through the hitch brackets and secure with the 1/8" hair cotter pin. See figure 3. 6. Assemble the vinyl cap onto the Hitch Control Tube. See figure 4. 7. Assemble the Control Cable to the Hitch Control Tube using the 1/4" x 2-1/4" carriage bolt and nylon wing nut. See figure 4. FIGURE 4 FIGURE 3 ASSEMBLY INSTRUCTIONS 1/4" x 2-1/4" HEX BOLT 1/4" HEX NUT VINYL CAP 1/4" HEX NUT 1/4" x 1-3/4" HEX BOLT 1/4" HEX NUT 1/4" x 1-3/4" HEX BOLT HAIR COTTER PIN HITCH PIN 1/4" x 2-1/4" CARRIAGE BOLT NYLON WING NUT VINYL CAP REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on page 3. OPERATION HOW TO USE YOUR SPREADER ADJUSTING THE FLOW RATE SETTING 1. Slide the Adjustable Stop to the desired setting. 2. Move the Flow Control Lever until it snaps into the Adjustable Stop, locking the lever at the desired setting. See figure 5. 5. FIGURE 6 5 1 3 7 10 OFF FLOW CONTROL LEVER ADJUSTABLE STOP FIGURE 5 USING YOUR SPREADER 1. Check the material package and the Spreader Settings sheet included with your spreader for the proper spreader setting and application rate. 2. Before filling spreader, move the control lever to the "OFF" position. 3. Move spreader onto a flat surface - either a walk or a driveway - and fill. 4. Set the Adjustable Stop to the desired setting. 5. Start the spreader in motion and then start the flow of material by moving the control lever until it snaps into the adjustable stop. NOTE: Always place control lever in the "OFF" position while filling spreader and when stopping or turning, to prevent release of excess fertilizer. APPLICATION TIPS 1. This unit will cover a 4 to 8 foot wide area depending on the material used and the towing speed. 2. To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. 3. For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips. See figure 6. 4. If lawn is odd shaped, spread a border around the edges and then spread between the border. See figure 6. Keep wheel approximately 4 feet from any area you do not wish to spread. IMPORTANT: Be careful when using spreader around ornamental plants because weed control chemicals can damage these plants. MAINTENANCE & STORAGE CHECK FOR LOOSE FASTENERS 1. Make a thorough visual check of the Spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. LUBRICATION 1. Apply a few drops of oil to all moving parts. CLEANING 1. Always empty spreader after each use, storing leftover material in it's original bag. 2. Wash the spreader and dry thoroughly after each use. STORAGE 1. Empty and clean the hopper as instructed in maintenance section. 2. Store in a clean, dry area. 5 6 HERRAMIENTAS NECESARIAS PARA EL ARMADO (2) Llaves de 11 mm 1. Coloque las tapas de vinilo sobre los extremos de los Tubos de Enganche de Mano Derecha y de Mano Izquierda. Vea la Figura 1. 2. Coloque el Tubo de Enganche de Mano Derecha en el tubo del marco del esparcidor, usando dos pernos hexagonales de 1/4” x 2-1/4” y dos tuercas hexagonales de 1/4”. No las apriete todavia. Repita la operacion con el Tubo de Enganche de Mano Izquierda. Vea la Figura 1. FIGURA 1 3. Coloque el Tubo de Control de Enganche entre los Tubos de Enganche, usando dos pernos hexagonales de 1/4” x 1-3/4” y dos tuercas hexagonales de 1/4”. Apriete todos los pernos y las tuercas. Vea la Figura 2. FIGURA 2 4. Coloque los Soportes de Enganche en el Tubo de Control de Enganche, usando dos pernos hexagonales de 1/4” x 1-3/4” y dos tuercas hexagonales de 1/4”. Apriete pernos y tuercas. Vea la Figura 3. 5. Haga pasar el pasador de enganche a traves de los soportes de enganche y asegure con el pasador de horquilla de 1/8”. Vea la Figura 3. 6. Coloque la tapa de vinilo en el Tubo de Control de Enganche. Vea la Figura 4. 7. Fije el Cable de Control en el Tubo de Control de Enganche, usando el perno...