Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• Insert hitch pin until it extends through bottom of Floating Hitch. Insert hair cotter pin into hitch pin. WARNING: Never fill fuel tank indoors, or with the engine running, or while the engine is hot. Do not smoke while filling tank. STOPPING YOUR TILLER TINES • Raise tiller to transport position. • Pull forward on tine clutch lever. ENGINE (Refer to separate engine manual.) • Move throttle control to "STOP" position. • Turn shut off to "OFF" position. • Never use choke to stop engine. STARTING YOUR TILLER (Refer to separate engine manual.) CAUTION: The muffler and adjacent areas are hot! • Check oil and gas in Tiller engine. • Attach spark plug wire to spark plug. • Pull forward on tine clutch lever to disengage tines. A safety switch prevents engine from starting while tines are engaged. • Turn shut off to "ON" position. • Move choke lever on engine to CHOKE position. (A warm engine may not require choking.) • Move throttle control lever on engine to FAST position. • Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Let the rope rewind slowly. • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter. • Repeat instructions in two preceding paragraphs until engine fires. When engine starts, move choke control gradually to RUN position. • Allow engine to warm up for a few minutes before engaging tines. FIG. 6 BREAKING IN YOUR TILLER Break-in your belts, pulleys and the control before you actually begin tilling. • Start engine with tiller attached to tractor in transport position. Engage Tine Clutch Lever to start tine rotation. Allow tines to rotate for five minutes. • Check tine operation and adjust if necessary. See "TINE OPERATION CHECK" in the Service and Adjustments section of this manual. OPERATION TRANSPORTING YOUR TILLER AROUND THE YARD • Pull forward on lift handle until it locks in the up, transport position. AROUND TOWN • Disconnect spark plug wire. • Drain fuel tank. • Transport in upright position to prevent oil leakage. TRANSPORTING YOUR TILLER AROUND THE YARD • Pull forward on lift handle until it locks in the up, transport position. AROUND TOWN • Disconnect spark plug wire. • Drain fuel tank. • Transport in upright position to prevent oil leakage. CUSTOMER RESPONSIBILITIES Refer to the engine manual for instructions on engine maintenance. Before each use 25 hrs. or every season 50 hrs. or every season Yearly First 5 to 8 hrs. 100 hrs. or every season MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Service Dates Check Engine Oil Level X Change Engine Oil X X* Service air cleaner precleaner X** Service air cleaner cartridge X** Replace spark plug X Clean cooling system X** Check valve clearance X Check for loose fasteners X Lubricate Tiller X Lubricate Tiller Transmission X * Change oil every 25 hours when operating the engine under heavy load or in high temperatures. * Clean more often under dusty conditions or when airborne debris is present. Replace air cleaner parts, if very dirty. CUSTOMER RESPONSIBILITIES ENGINE MAINTENANCE WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or before performing any repairs or maintenance. • Check oil level before each use and every 8 hours. • Maintain engine oil as instructed in the separate engine manual. • Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced. To service the air cleaner, refer to the separate engine manual. • Spark plug replacement is recommended every 100 hours or yearly. Check the engine manual for correct plug type and gap specifications. SERVICE AND ADJUSTMENTS WARNING: Shut off (disengage) the Tine Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. TO REPLACE V-BELT Replace V-belt if it has been damaged considerably from slipping under heavy loads or if it show cracks or frayed edges. Refer to figures 11 and 12. IMPORTANT: Do not move or remove the belt guide. If the position of the belt guide is accidentally altered, return it to the correct setting (6-1/2" above the tine shield support plate). • Remove the screw from the top of the belt guard. • Remove the hex nut from the rear of the guard. • Remove the belt guard to allow access to drive belt. • Disengage tine clutch lever and remove belt. • Reverse above procedures for installation of new belt. FIG. 12 FIG. 11 SERVICE AND ADJUSTMENTS WARNING: Shut off (disengage) the Tine Clutch Lever, the Tiller Engine and the Tractor Engine before making any repairs. TINE CARE • For best results — Tine Blades should be kept reasonably sharp. The Tine Blade can be sharpened on a grinding wheel. Do not attempt to sharpen Tines while they are mounted to...