Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
NOTE: Do not tighten hardware at this time. (See Figure C.) FIGURE CHEX BOLT(32) GEAR BOX & AXLE(39) HOPPER(16) LOCK NUT(24) WHEEL ASSY. FRAME(20) Attach one end of the Frame Braces 4. (31) to the Hopper Frame (30), using two Bolts (33) and two Lock Nuts (24). Then attach the other ends of the Frame Braces, with the Cross Brace (45) positioned between the Frame Braces, to the Wheel Assembly Frame (20), using two Bolts (11). NOTE: Do not tighten hardware at this time. (See Figure D.) FIGURE DLOCK NUT(24) CROSS BRACE(45) FRAME BRACE(31) BOLT(33) BOLT(11) HOPPER(16) Slide an Axle Bushing (37) over the 5. Axle (39) and into an Axle Bearing (38) on both ends of the Axle. Install a Wheel (36) on each end of the Axle and secure the Wheels using two Hex Bolts (47) and two Hex Lock Nuts (44). Then install a Flat Washer (34) and End Cap (35) for each Wheel. (See Figure E.) FIGURE EAXLE BUSHING(37) WHEEL(36)END CAP(35) FLATWASHER(34) HEX BOLT(47) HEXLOCK NUT(44)HOPPER(16) THREADED HOLE Note: Find the threaded hole in one side of Axle. Install a Wheel (36) on this end of the Axle and secure the Wheel using one Hex Bolt (47) and one Lock Nut (44). Then install a Flat Washer (34) and End Cap (35) for this Wheel. Install the other Wheel on the Axle and secure it in place with a Flat Washer (34) and End Cap (35). REV 09b Insert the Handle Shaft (26) between 6. the two Wheel Assembly Frames (20). Attach the Pivot and Bracket Assembly (19) to the Wheel Assembly Frames and Handle Shaft, using two Bolts (11) and two Nuts (21). (See Figure F.) FIGURE FHANDLE SHAFT(26) WHEEL ASSY. FRAME(20) NUT(21) BOLT(11) PIVOT& BRACKETASSY. (19) HOPPER(16) 7. The Upper Handle (23) features three positions for operating comfort. To use the middle or upper positions, place the Handle Spacer (1) between the mounting holes nearest to the Handle Covers (15). Insert a Bolt (11) through the Upper Handle (23), through the Handle Spacer, through the other Upper Handle and secure with a Flat Washer (48) and Nut (21). Install the Gauge & Lever Assembly (4) on the left hand side, using two Bolts (11) and two Nuts (21). (See Figure G.) Unscrew and remove 8. one Lock Nut (24) from the Control Rod (25). Insert the threaded portion of the Control Rod into the hole in the Pivot and Bracket Assembly (19). Then re-thread the Lock Nut back onto the Control Rod. (See Figure H.) Insert the Adjust Connect Rod (46) into 9. the Shut Off Plate (27). Then secure the Adjust Connect Rod to the Shut Off Plate, using one Flat Washer (48) and HANDLE SPACER (1) UPPER HANDLE (23) FLAT WASHER (48) NUTS (21) GAUGE & LEVER ASSY. (4) BOLT (11) FIGURE G FIGURE H CONTROL ROD (25) PIVOT & ASSY. BRACKET (19) LOCK NUT (24) one Lock Nut (24). (See Figure I.) FIGURE IHOPPER(16) FLATWASHER(48) LOCKNUT(24) 10. Push down on the Adjust Handle (6) to its lowest position. (See Figure J.) FIGURE J“R” PIN (17) “R” PIN(17) WINGNUT(10) LOCK NUTS(24) PUSH FORWARD. IMPELLER MUST TURNIN THIS DIRECTION. ADJUSTHANDLE(6)PINIONSHAFT 11. Adjust the position of the two Lock Nuts (24) on the Control Rod (25), making sure the holes at the bottom of the Hopper (16) line up with the holes in the Shut Off Plate (27) properly. (See Figures I and J.) Pull up on the Adjust Handle (6) to its 12. upper position, making sure the holes in the Hopper (16) and the holes in the Shut Off Plate (27) are 100% open. (See Figure J.) Adjust the position of the Wing Nut 13. (10). By doing so, you are able to control the size of the holes you need. (See Figure J.) Insert the “R” Pin (17) into the Pinion 14. Shaft on the Gear Box and Axle Assembly (39). Make sure the Impeller (42) is turning in the correct direction as indicated by the arrow in the illustration. (See Figure J.) Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before assembly or use of this product. Before operating the Spreader make 1. sure to wear ANSI-approved safety impact glasses, NIOSH-approved dust mask/respirator, and heavy duty work gloves. Remove the Screen (14) on the Hopper 2. (16) and fill the Hopper with the material you wish to apply. Do not exceed 50 pounds of material. Then replace the Screen. (See Figure K, next page.) Refer to the manufacturer’s recom3. mended flow rate (0 to 5, typically shown on the bag/container of the material being applied). Adjust the flow rate on the Gauge and 4. Lever Assembly (4) to that of the mate SHUT OFF PLATE (27) rial manufacturer’s recommendation. To do so, move the Wing Nut (10) to the proper setting. (See Figure K.) Grip the Upper Handles (23) with 5. both hands, pull the Adjust Handle (6) back and immediately begin pushing the Spreader at a slow and even rate over the area you wish to apply. (See Figure K.) IMPORTANT: 6. Always PUSH the Spreader when applying material. When pulled backward while the Hopper (16) is open, the Spreader may apply an excessive amount of material. (See Figure K.) When finished ap...