Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. 4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension. ASSEMBLY OF POLE SAW Step . – Squeeze Trigger Push in and hold trigger lockout button. Squeeze and hold trigger.1A 1B Step . – Insert Pole Bracket into Saw Insert pole bracket into saw. Note:Pole Bracket holds trigger in “ON” position. 2B Continue to hold trigger while completing step 2B. 2A 111219 14 111219 15 ASSEMBLY Continued Continued TIGHTEN Step . – Attach Handle Bracket to Pole Bracket Slide handle bracket onto clamping bolt. Clamping bolt should extend through handle bracket Step . – Secure Handle Bracket to Pole Bracket Place lockwasher onto clamping bolt. Thread knob onto clamping bolt. Note: After knob makes contact with handle bracket, tighten 1 1/2 to 2 more turns. Step . – Connect to Power Cord Plug saw power cord into receptacle cord at end of inner pole. 3A 3B 5A 4B 4A OPERATING CHAIN SAW EXTENSION CORDS Use proper extension cords with this Pole Saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below. WARNING: Read and understand this owner’s manual before operating this Pole Saw. Make certain you read and understand all Important Safety Information, pages 2 through 4. Improper use of this Pole Saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood. Cord Length AWG Cord Size 25 feet 16 AWG 50 feet 16 AWG 100 feet 16 AWG 150 feet 14 AWG Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords. The extension cord may come undone from the power cord during use. To avoid this, make a knot with the two cords as shown in Figure 5. ADJUSTING POLE LENGTH The Remington Pole Saw has a telescoping pole assembly that will extend from 57 inches (fully retracted) to 96 inches (fully extended). A cam levered collet is used to hold the pole in position at any extended length. 1. To extend the pole, loosen the clamping lever as shown in Figure 6. Pole will slide freely. 2. Pull inner pole section out to desired length of extension. Note: Only extend pole to minimum length required to reach limb that is being cut. 3. To lock pole in position, tighten clamping lever as shown in Figure 6. OPERATING CHAIN SAW Continued OILING CHAIN Always check oil level before using saw. Do not attempt to operate the oil system while saw is in operation. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least once before each cut. Check oil level often by looking at oil sight level hole. Oil sight level hole is on left side of saw, between front handle and front hand guard. CUTTING WITH THE POLE SAW 1. Connect saw to extension cord. Connect extension cord to power supply. 2. Use both hands to grip Pole Saw. Use only designated grip areas when operating Pole Saw (see Figure 7). Use firm grip. Thumbs and fingers must wrap around Pole Saw handle and pole. 3. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. 4. When ready to make a cut, press in trigger switch lock-out and squeeze trigger switch (see Figure 8). This will turn Pole Saw on. Releasing trigger switch will turn Pole Saw off. Make sure saw is running at full speed before starting a cut. 5. When starting a cut, place moving chain against wood. Hold Pole Saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw. 6. Guide Pole Saw using light pressure. Do not force Pole Saw. The motor will overload and can burn out. It will do the job better and safer at the rate for which it was intended. 7. Remove Pole Saw from a cut with saw running at full speed. Stop Pole Saw by releasing trigger. Make sure chain has stopped before setting Pole Saw down. TRIMMING A TREE (PRUNING) CAUTION: Seek professional help if facing conditions beyond your ability. Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree. 1. Make first cut six inches from tree trunk on underside of limb. Use top of guide bar to make this cut. Cut 1/3 through diameter of limb (see Figure 9). 2. Move two to four inches farther out on limb. Mak...