Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
FERTILIZER PARTICLE SIZE BAG RATE Pounds of fertilizer used per 1,000 sq. ft. of coverage APPROX. SETTING SPREAD WIDTH Large, heavy particles 5 10 15 3 1/2 4 4 1/2 8 8 8 Medium-mixed particles 5 10 15 2 1/2 3 1/2 4 8 8 8 Small particles (nitrogen) 1 2 3 2 2 1/2 3 8 8 8 Mixed size particles- some fines 5 10 15 3 3 1/2 4 6 6 6 Light weight particles 5 10 15 2 2 1/2 3 4 To 6 Conversions should be used as guidelines for establishing proper rate settings. To obtain the most accurate application rate, follow the procedures described in the Effective Pattern Width and Application Rate sections. The settings shown here are only approximations and will vary due to physical characteristics of the product, walking speed, turf condition, humidity, etc. Warranty and guarantees of actual coverage or uniformity are neither expressed nor implied. MAINTENANCE Never store unused material in spreader. 1. Return unused product to its original container. Oil Impeller Shaft Bearing In Hopper Wash spreader thoroughly after each use 2. and dry completely in sun or heated area. Oil Oil the axle bearings, impeller shaft bearing 3. in hopper, control knob in T-handle. Remove gear cover and wash gears 4. thoroughly. Oil all bearing areas and face of gear teeth. Re-install gear cover. Gear mesh should be checked on a regular 5. basis during high use periods. Clearance between the axle gear and pinion gear should be minimal but not tight. If adjustment is necessary, loosen axle collar set screw and hold gears together. Slide axle collar against the gear support and tighten axle collar set screw. Spin drive wheel. Gears should run freely and smoothly. Axle Collar Impeller surface should be cleaned periodically 6. to remove build-up of product. Build-up can cause the spread pattern to change. Oil Tire pressure should be 20-25 PSI. 7. Oil WARRANTY Shindaiwa Inc. manufactures its products to superior standards of quality to ensure customers obtain the highest level of satisfaction. In keeping with this goal, Shindaiwa Inc. warrants the unit to the original purchaser as follows: WARRANTY PERIOD One year from the delivery date to the original purchaser for consumer and commercial applications.90 days for rental applications. WARRANTY ADMINISTRATION Within the covered warranty period, Shindaiwa Inc. will, at their option, repair or replace any defect in material or workmanship, without charge for parts or labor, if this product is presented at an authorized Shindaiwa dealer. WARRANTY EXCLUSIONS AND LIMITATIONS Shindaiwa Inc. assumes no responsibility for damages, loss, or injury resulting from: . Normal wear and tear . Misuse or neglect . Modifications to or removal of original component parts The warranty is limited to the terms stated herein. Shindaiwa Inc. disclaims all liability for incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so these limitations may not apply to you. This warranty give you specific legal rights, and you may also have other rights which may vary from state to state. Shindaiwa reserves the right to change the design or specifications of this product without obligation to modify previously manufactured products. OWNER’S RESPONSIBILITIES The owner of the unit must demonstrate reasonable care in the use, maintenance, and storage of this Shindaiwa product. If a warrantable failure should occur, the owner must deliver the product to an authorized Shindaiwa servicing dealer for correction. All residual chemicals must be flushed from the tank prior to delivery. Unidentified chemicals left in the tank can pose a serious health threat to anyone servicing the unit and unaware of its presence! To obtain warranty service, proof of purchase must be presented to the authorized Shindaiwa servicing dealer when the product is presented for repairs. Proof of purchase must include date of purchase and the name and address of the selling dealer. Parts List for SHINDAIWA MODEL 41RS 16 17 18 19 1 23 15 10 13 5 14 3 2 12 22 11 6 4 8 21 9 7 13 PART OF OUR SERVICE IS PROVIDING REPLACEMENT PARTS. Parts may be obtained through your local distributor. be sure to give: 20 SPREADER MODEL NUMBER 1. SPREADER NAME2. 11975 SW Herman Rd. PART NUMBER3. Tualatin, Or. 97062 NAME OF PART AS SHOWN 4. 503-692-3070 Fax 503-692-6696 com P / N 82010 Key No. Description Part No. Key No. Description Part No. 1 Hopper Ass’y-includes #2 & 3 15845 13 Drive & Free Turning Wheel 14939-1 2 Rate Cam & Chute Assembly 14455-1 14 Handle Braces (2) 13613-1 3 Shutoff Plate 14454-1 15 Handle Tube 14513-1 4 Impeller Assembly 15849 16 T-Handle Assembly 13634-2 5 Frame Assembly 15837 17 Control Knob Spring 14462 6 Legs (2) 13619-1 18 Control Knob & Wire Ass’y 13640-1 7 Axle 15842 19 Wire Retaining Clip 13643-1 8 Axle Collar 13362 20 Gear Cover Assembly 13623-1 9 Axle Bushings (2) 12696 21 Fastener Package 15880 10 Impeller Shaft Bearing 15833 22 Hopper Cover 15209 11 Axle Gear 13625-1 23 Handle Grip...
Este manual também é adequado para os modelos :Ferramentas para Jardim - HomePro 41RS Broadcast (2.69 mb)