Assessments - 2, GPA: 4 ( )

Fabricante : McCulloch Arquivo Tamanho: 1.15 mb Arquivo Nome : Língua de Ensino:

The warranty may be invalidated due to erroneous adjustments made by personnel not belonging to authorized service centers. H. Routine maintenance 1 2 3 4 7 9 10 17 H1. After every use In order to avoid overheating the motor, remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Store the machine in a dry place. After 25 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air. For more thorough cleansing, you can wash it with soapy water. After 50 hours of use Add some high speed gear grease in the gearbox through hole (C). Remove and clean the spark plug (set the space between the electrode at 0.5/0.6 mm). Replace if excessively encrusted. In case of excessive encrustation check the carburetor adjustment, the percentage of oil in the fuel mixture and make sure the oil is of excellent quality and suitable for two-stroke engines. After 100 hours of use Replace the spark plug. Every three months Contact your Service Center for a complete overhaul, replacement of the fuel filter and cleaning of the parts inside the machine. This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine. Periods of prolonged disuse See "Environmental information". If you use the machine in an exceptionally dirty or dusty environment these operations should be carried out more often. H2. Replacement of nylon string To replace the reel of string, press both the release pawls indicated by the arrows, remove the empty reel, unroll any string left and rewind the new string. Open the original package of string and insert the ends of the two strings in the eyelets on the reel, then wind the strings completely on the reel in the same direction and fasten the end of each string in the 2 opposite grooves. Replace the reel in its housing and thread the ends of the strings in their bushings. Pull each string so that about 15 cm comes out on each side. Reassemble the nylon string head as shown. If the reel becomes excessively worn, replace it with a whole new reel. H3. Attachments maintenance Follow maintenance instructions on the attachment manual. I. Techniques for use 1 4 5 6 7 8 9 speed as running it at top speed without a load can damage the engine severely. The machine is ideal to complete the work of the cutting stage, decelerate the engine to minimum lawnmover. In fact, it can reach places where a Cutting techniques engine running at high speed. After every 10 11 12 13 14 16 17 Wait until the engine is running at minimum speed before moving the machine from one section to another. ENGLISH - 7 normal lawnmower is unable to go. Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees. Mowing To prevent damage to your lawn or the cutting mechanism, keep the string parallel to the ground but avoid contact with the terrain. Trimming borders Angle the nylon string head keeping it a short distance from the ground. Cut using the end of the string. Do not press the string against the material to be cut. I1. Drawing out the string During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. Tap gently on the ground with the button (A) as shown in the figure and the string will come out automatically. Accelerate again. If the string does not come out make sure there is still some left and try again. I2. Thinning grass with the grass cutter blade 2 16 The grass is cut with swinging motions from side to side, maintaining the blade parallel to the ground. During the right to left swing the grass is cut, while the backswing must be made without using the blade. KICKBACK can occur when cutting is done with the risk sector of the blade; we recommend cutting with the rest of the blade. Take care that the cup supportin...

Baixe o seu

Para fazer o download, introduza 2 dígitos :