Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
ON OFF BLAST On/Off Control Switch Used to start and stop the spinner. (Emergency Stop-OFF Position) Starting the Motor WARNING Before starting the spreader, the driver shall verify all bystanders are a minimum of 25 feet away from operating spreader. 1. Set the power switch to the ON position to start the motor. The motor will start immediately. The power switch will remain in this position. Blast Position Move and hold the power switch to the BLAST position for as long as momentary operation is needed. When released, the switch will automatically return to the OFF position and stop the motor. Stopping the Motor 1. Set the power switch to the OFF position to stop the motor. The power switch will remain in this position. The power switch OFF position operates as emergency stop when required. NOTE: Always place the cover on the hopper to prevent moisture buildup. Do not let the spreader sit idle with material in the hopper for an extended period of time. This can cause the material to compact and reduce or stop the flow of material. CAUTION Do not swing spreader with material in the hopper. NOTE: The truck ignition must be on to start the spreader. NOTE: If the truck ignition is turned off while the spreader is running, the motor will stop. Lit. No. 94430/94431 11 April 1, 2005 OPERATING THE SPREADER Variable Speed (PWM) Control START BLAST ON OFF 1 (Emergency StopOFF Position) 23 SPINNER MIN MAX 1 2 3 4 5 6 7 9 SPEED 8 1. Power Switch - used to start and stop the spinner. The power OFF position switch operates as emergency stop when required. 2. Speed Dial - used to change the speed of the spinner. 3. Indicator Lights - indicate whether the spinner is in motion. Left light is red and indicates a fault. Right light is green and indicates power is on. Starting the Motor with Variable Speed (PWM) Control WARNING Before starting the spreader, the driver shall verify all bystanders are a minimum of 25 feet away from operating spreader. Stopping the Motor with Variable Speed (PWM) Control 1. Set the power switch to the OFF position to stop the motor. The power switch will remain in this position. This is also the emergency stop position. NOTE: Always place the cover on the hopper to prevent moisture buildup. Do not let the spreader sit idle with material in the hopper for an extended period of time. This can cause the material to compact and reduce or stop the flow of the material. CAUTION Do not swing spreader with material in the hopper. NOTE: The truck ignition must be on to start the spreader. NOTE: If the truck ignition is turned off while the spreader is running, the motor will stop. 1. To start the spreader motor, press the power switch to the START/BLAST position and release. This is a momentary position and the power switch will automatically return to the ON position when released. The spreader will operate at the speed selected on the speed dial. 2. To increase the speed of the spinner rotate the speed dial clockwise. 3. To decrease the speed of the spinner rotate the speed dial counterclockwise. April 1, 2005 12 Lit. No. 94430/94431 REMOVING THE SPREADER CAUTION During removal or mounting, securely grip spreader to avoid dropping. NOTE: Empty the hopper before removing the spreader. Removing the Fixed Mount Spreader 1. Unplug the spreader and stoplight (if equipped). 2. Remove the two 3/8" cap screws, washers, and locknuts that fasten the spreader to the bumper of the vehicle. 3. Use an additional person or clamps to support the unit and then remove the four 3/8" cap screws and locknuts that fasten the spreader to the top brackets. 4. Remove the spreader from the vehicle and stand in an upright position. This may require additional support. Removing the Fixed Mount Brackets 1. Remove the two 1/2" cap screws, washers and locknuts that fasten the top bracket to the bed rail. 2. Remove the two 5/16" cap screws, washers and locknuts that fasten the top brackets the side of the bed rail. 3. Package the brackets with all hardware and store with the unit. NOTE: Empty the hopper before removing the spreader. Removing the Receiver Mount Spreader 1. Unplug the spreader. 2. Remove the pin from the receiver hitch. 3. Remove the spreader from the vehicle and stand in an upright position. This may require additional support. NOTE: Empty the hopper before removing the spreader. Removing the SWING AWAY® Spreader 1. Unplug the spreader and stoplight (if equipped). 2. Remove the hitch pin from the latch side hinge pin. 3. Remove the 1/4" cap screw and locknut from the hinged side hinge pin. 4. Use an additional person to support the unit and remove both hinge pins. 5. Remove the spreader from the vehicle and stand in an upright position. This may require additional support. Removing the SWING AWAY Top Brackets 1. Remove the two 1/2" cap screws, washers and locknuts that fasten the top bracket to the bed rail. 2. Remove the two 5/16" cap screws and locknuts that fasten the top bracket to the side of the bed rail. 3. Mar...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 2000-(20364) (357.85 kb)