Assessments - 4, GPA: 4.5 ( )

Fabricante : Land Pride Arquivo Tamanho: 2.66 mb Arquivo Nome : Língua de Ensino:

Tighten all nuts and bolts to torque as indicated in the “Torque Values Chart” on page 24. Front Rubber Guard (RCR1560 & RCR1572) Figure 2-3 18334 Rubber Guards (RCR1542 & RCR1548) Install front rubber guard (#1), rear rubber guard (#2) and front and rear straps (#3) and (#4) as shown in Figure 2-5, with 3/8” x 1” long carriage bolts (#5), and 3/ 8” flange nuts (#6). Tighten all nuts and bolts to torque as indicated in the “Torque Values Chart” on page 24. Safety Guards ! DANGER Rotary cutters have the ability to discharge objects at high speeds; therefore, the use of front and rear safety shields is strongly recommended when cutting along highways or in an area where people may be present. 13 Section 2: Options 12/28/05 RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M Land Pride Table of Contents Front Chain Guard (RCR1560 & RCR1572) Install each segment of the front chain guards (#1) as shown in Figure 2-4, with 3/8” x 1” long carriage bolts (#2), and 3/8” flange nuts. Tighten all nuts and bolts to torque as indicated in the “Torque Values Chart” on page 24. Rear Chain Guard (RCR1560 & RCR1572) Install the rear chain guard (#1) as shown in Figure 2-5, with 3/8” x 1 ” long carriage bolts (#2), and 3/8” flange nuts. Tighten all nuts and bolts to torque as indicated in the“Torque Values Chart” on page 24. Front Chain Guard Figure 2-4 Rear Chain Guard Figure 2-5 16346 16373 Table of Contents Section 3: Operating Instructions Transporting ! CAUTION When traveling on public roads at night or during the day, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws. IMPORTANT: Always disengage the tractor’s PTO before raising the cutter to transport position. 8. When raising the cutter to the transport position be sure that driveline does not contact tractor or cutter. 9. Be sure to reduce tractor ground speed when turning; and, leave enough clearance so the cutter does not contact obstacles such as buildings, trees or fences. 10. Limit transport speed to 20 mph. Transport only with a farm tractor of sufficient size and horsepower. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely. 11. When traveling over rough or hilly terrain, shift tractor to a lower gear. Operating Check List In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved in the operation, transport, maintenance and storage of equipment. Before beginning to cut, the following inspection should be performed. Operating Checklist ! DANGER To prevent personal injury caused by thrown objects, the use of front & rear safety guards is strongly recommended! To avoid injury or death from entanglement in rotating drivelines, the drive gearbox shields must be in place and secure when operating. ! CAUTION0Damage may occur if exceeding the rated cutting capacity of the cutter! ! CAUTION Do not over speed PTO or machine damage may result. This cutter is designed to be used with the tractors having a 540 RPM rear PTO. Know what your tractor requirements are. Cutting Instructions 1. Your cutter is equipped with free swinging cutting blades to reduce shock loads to the cutter if striking obstacles. 2. Start the machine slowly; do not use full throttle. Allow 10 seconds for cutter blades to become aligned properly before going to full power. 3. The ground speed depends on two things: the density of the material being cut, and the size of the tractor. Never run fast enough to overload the tractor. 4. It is important to maintain correct RPM PTO speed. Loss of PTO speed will allow the blades to hinge back and result in ragged, uneven cutting. 5. This cutter was designed to cut grass and brush 1” maximum diameter in right-of-ways, pastures and for shredding row crop residues. Check Reference “Important Safety Information” in this Manual. Section 1 page 1 Check oil level in gearboxes. Section 4 Page 19 Check that all plugs in gearbox have been replaced properly. Section 4 Page 19 Be sure nuts and bolts are tight. Section 1 Be certain all guards and shields are in place. Section 1 page 1 Lubricate the cutter as needed. Refer to “Maintenance and Lubrication”. Section 4 Page 19 14 RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M 12/28/05 15 Section 3: Operating Instructions 12/28/05 RCR1542, RCR1548, RCR1560 and RCR1572 Rotary Cutters 312-556M Land Pride Table of Contents Leveling Procedure There are 4 primary adjustments that should be made prior to actual field operations: i. Deck level from left to right j. Tractor top link length k. Tractor lower link height l. Tailwheel height Proper adjustment of each of these items will provide for higher efficiency, improved cutting performance and longer blade life. The following tools will be needed: a. Pliable tape measure b. Spirit or carpenters level c. Open end or ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :