Assessments - 3, GPA: 3.7 ( )

Fabricante : Classen Arquivo Tamanho: 1.1 mb Arquivo Nome : Língua de Ensino:

9. Servicing the sod cutter regularly and correctly. 10. Classen Mfg., Inc. parts and service. 11. Give the customer the operators manual and encourage customer to read it. DATE DELIVERED __________/__________/__________ SIGNATURE _______________________________________ SAFETY ENGINE STARTING PROCEDURES HANDLE FUEL SAFELY -AVOID FIRES Handle gasoline with care; it is highly flammable. Use an approved gasoline container. Fill the fuel tank outdoors. DO NOT fill tank completely full. DO NOT smoke while you fill fuel tank. DO NOT remove gas cap if engine is running. READ SAFETY SIGNS Carefully read and follow all caution stickers. WARNING ALL GUARDS MUST BE IN PLACE WHILE MACHINE IS IN OPERATION WARNING KEEP HANDS & FEET AWAY FROM MOVING PARTS OPERATE SAFELY Carefully read this manual and operate sod cutter correctly. PROTECT CHILDREN Keep children and pets out of the area where you are cutting sod. AVOID TIPPING Make sure you do not get too close to sharp drop-offs to avoid tipping sod cutter over. OPERATE SAFELY ON SLOPES You may cut sod any direction on slopes, however, make sure you do this carefully. Cutting on slopes can be dangerous. To avoid any accidents, make sure to leave yourself room to correct the problem if one arises. Always park your sod cutter on level ground. PRACTICE SAFE MAINTENANCE Keep all machine parts in good condition and fastened in place. Fix damages immediately. Replace worn or broken parts. Whenever you work on the sod cutter, disconnect spark plug wire. START ENGINE SAFELY Make sure hands and feet are out of the way of moving parts when starting engine. NOTICE: There are two locations on this engine that require oil, both the crankcase and the transmission (gearbox). Running the engine or gearbox with a low oil level can cause engine damage. Refer to the engine manual for complete engine information and recommendations. ENGINE OIL LEVEL CHECK 1. BEFORE CHECKING ENGINE: • make certain the engine is level • the engine switch is in the OFF position • the sod cutter blade is NOT engaged • the drive wheels are disengaged. 2. Remove the filler cap/dipstick and wipe it clean. 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the oil level is low, fill to the edge of the oil filler hole with the recommended oil. SAE 10W-30 is recommended for general use. Refer to engine oil recommendations in engine manual for other viscosities and information. 5. Screw in the filler cap/dipstick securely. TRANSMISSION OIL LEVEL CHECK 1. Check the transmission oil level with the engine stopped and in a level position. 2. Remove the filler cap/dipstick and wipe it clean. 3. Insert and remove the dipstick without screwing it into the filler hole. Check the oil level shown on the dipstick. 4. If the oil level is low, add oil to reach the upper limit mark on the dipstick. Use the same oil that is recommended for the engine, SAE 10W-30. 5. Screw in the filler cap/dipstick securely. STARTING ENGINE 1. Turn fuel cock to the "open" position. 2. Turn choke on (closed). 3. Turn ignition switch to "on". 4. Move throttle lever on engine to half throttle position. 5. Pull recoil starter rope until engine starts. 6. After engine is warm, turn off choke (open). 7. Allow engine to run one minute before cutting sod. 8. Check engine rpm setting before operating. DO NOT exceed 3600 rpm. STOPPING ENGINE 1. Turn throttle to "slow" position. 2. Turn off ignition switch. OPERATING THE SOD CUTTER BLADE ANGLE (PITCH) PREPARATION 1. Police lawn area for obstacles and debris (i.e. sprinklers, hoses, toys, etc.). Remove all items. 2. Make sure underground sprinkler heads and other hidden obstacles are marked to prevent damage. 3. Mark other areas where sod cutting will be a problem or too risky (i.e. mud, tree roots, steep hills). OPERATING 1. Start the engine. CAUTION: To avoid injury, do not place your feet or other body parts under the blade while starting the engine. 2. Select the correct cutting depth desired up to 2 1/2 inches. Loosen the tee handle from the depth gauge plate, located under the height adjustment bar, (#3 on illustration) and put it to the correct height setting. Tighten the tee handle. 3. Push the wheel drive handle (#5 on illustration) and the cutter blade handle (#4 on illustration) to the "on" position toward the engine. 4. Raise the main handle upward so the front nose of the sod cutter rests on the ground. 5. Loosen the 1/2" handle nut (#2 on illustration) and lower the height adjustment bar to rest on the depth gauge. Now tighten the 1/2" handle nut securely so it will not loosen with the vibration of the machine. 6. Go to the back of the machine and lower the handle until the cutting blade rests on the ground. You are now ready to cut sod. 7. Turn the throttle to the desired operating speed by t...

Baixe o seu

Para fazer o download, introduza 2 dígitos :