Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
brushcutter. : Go to "Mounting the Mowing Head". : Always fit stop (6) when you use a circular saw blade. If you want to mount a metal cutting : Place the stop on the gearhead tool in place of a mowing head, you flange. Mounting hardware is not packed will need the following additional : Fit the three M 5 x 18 screws (7) and with the machine parts: Nut (3), rider plate (4) and tighten down securely. Only mowing heads may be thrust washer (5) (special mounted. accessories). FS 80, FS 80 R, FS 85, FS 85 R English / USA Mounting hardware is packed with the machine Mowing heads and metal cutting tools may be mounted. Mounting hardware is loose : Pull the hose (1) (protector for shipping) off the shaft (2). The nut (3), rider plate (4) and thrust washer (5) are in the parts kit supplied with the machine. : Go to "Mounting the Mowing Head" or "Mounting Metal Cutting Tools". Mounting hardware is secured to gearhead : Go to "Removing Mounting Hardware" Removing Mounting Hardware : Block the shaft – see next section on "Blocking the Output Shaft". : Use the combination wrench (6) (supplied with machine or available as special accessory) to unscrew the nut (3) clockwise (left-hand thread) from the shaft (2). : Pull the thrust washer (5) off the shaft (2). The rider plate (4) is in the parts kit supplied with the machine. : Go to "Mounting the Mowing Head" or "Mounting Metal Cutting Tools". Blocking the Output Shaft 7 8 2 002BA166 KN7 : Insert the stop pin or screwdriver (7) (supplied with machine or available as special accessories) in the hole (8) in the gearhead as far as stop – apply slight pressure. : Rotate nut or cutting tool on the shaft (2) until the stop pin slips into position and blocks the shaft. FS 80, FS 80 R, FS 85, FS 85 R English / USA 1 002BA081 KN Mounting the Mowing Head Keep instruction sheet for mowing head in a safe place. : : : Screw the STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 counterclockwise onto the shaft (1) as far as stop. Block the output shaft. Tighten down the mowing head. Remove the tool used to block the shaft. STIHL FixCut 25-2 : Place the mowing head on the thrust plate (2). Collar (arrows) must locate in the mowing head’s mounting hole : Push the thrust washer (3) over the shaft (1) so that it locates against the base. : Block the output shaft. : Screw the mounting nut (4) with the combination wrench (5) counterclockwise on to the output shaft and tighten down firmly. Remove the tool used to block the shaft. Removing the Mowing Head : Block the output shaft. STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 : Unscrew the mowing head clockwise. STIHL FixCut 25-2 : Use the combination wrench to unscrew the mounting nut clockwise from the output shaft If the mounting nut is too loose, fit a new one Adjusting Nylon Line STIHL SuperCut Fresh line is advanced automatically if remaining line is still min. 2 1/2" (6 cm) long. The blade on the deflector trims overlong line to the correct length. FS 80, FS 80 R, FS 85, FS 85 R English / USA STIHL AutoCut : Hold the rotating mowing head above the ground – tap it on the ground once – about 1 1/4" (3 cm) fresh line is advanced. The blade on the deflector trims overlong line to the correct length – avoid tapping head more than once at a time. Line feed operates only if both lines still have a minimum length of 1" (2.5 cm). All other mowing heads Refer to the instructions supplied with the mowing head. To reduce the risk of injury, always shut off the engine before adjusting the nylon line by hand. Replacing Nylon Line or Cutting Blades Refer to the instructions supplied with the mowing head. Mounting Metal Cutting Tools Remove the skirt and blade from the mowing head deflector before mounting grass cutting blade 230-4 (1), grass cutting blade 230-8 (2), or brush knife (3) – see “Mounting the Deflector” Fit the appropriate limit stop before mounting the circular saw blade 200 (4,5) – see “Mounting the Deflector”. : Lay your machine on its back with the gearhead facing upward. Cutting edges of (1) and (3) may point in either direction. Cutting edges of (2), (4) and (5) must point clockwise. Direction of rotation is marked by arrow on inside of cutting head deflector or limit stop. FS 80, FS 80 R, FS 85, FS 85 R English / USA Fuel : Place the cutting tool (6) on the thrust plate (7). Collar (see arrows) must locate in cutting tool’s mounting hole. : Slip thrust washer (8) and rider plate (9) over the output shaft (10). : Block the output shaft and : Screw the mounting nut (11) with the combination wrench (12) onto the output shaft counterclockwise and tighten down firmly. If the mounting nut is too loose, fit a new one. Removing cutting tool : Block the output shaft. : Unscrew the nut clockwise. : Removing the cutting tool – do not remove the thrust plate (7). This engine is certified to operate on unleaded gasoline and the STIHL two- ...
Este manual também é adequado para os modelos :Ferramentas para Jardim - FS 80, FS 85 (3.48 mb)