Assessments - 5, GPA: 4.2 ( )

Fabricante : Zenoah Arquivo Tamanho: 278.88 kb Arquivo Nome : Língua de Ensino:

• These engines are certified to operate on unleaded gasoline. • Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL) • If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur. • Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment. • Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine. ¦ HOW TO MIX FUEL Pay attention to agitation. IMPORTANT WARNING [BC3501LE/WE/BC4501WE] • Using attached 4 socket screws, secure the connection firmly with equal force. ¦ HANDLE [BC2311LE/BC2611LE/BC3501LE] • Put the handle onto the main pipe and fix it with 4 screws. [BC2611WE/BC3501WE/BC4501WE] 1. Loosen the 4 bolts on the upper cap and insert the handles equally. Retighten the bolts. 2. Put the handle assembly into the bracket and put the upper cap over it. Tighten the cap securely. ¦ CONNECTING THROTTLE WIRE 1. Remove the air cleaner cover. 2. Connect the end of the throttle wire to the joint on the top of the carburetor. ¦ CONNECTING SWITCH WIRES • Connect the switch wires between the engine and the main unit. ¦ PROTECTOR [BC2611WE/BC3501WE/BC4501WE] • Wrap the protector around the outer pipe as shown in the figure, and fasten the magic fastener. ¦ INSTALLING DEBRIS GUARD 1. Fit the guard skirt on debris guard. 2. [BC2311LE/BC2611] Attach the debris guard with the bolts provided while inserting the spacer between the guard and the pipe. [BC3501/BC4501WE] Attach the debris guard with the bolts provided to the pipe. ¦ INSTALLING LINE HEAD 1. While locking the gear shaft by inserting the angled bar(1) into the holder(A)(2) on the gear box, loosen and remove the nut(left-handed) 2. Fit the line head assembly to the gear shaft. Tighten it securely by hand. ¦ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1. Feed fuel into the fuel tank and tighten the cap securely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine. 3. Push the primer pump several times until overflown fuel flows out in the clear tube. (1) Choke lever (2) Close (3) Open (4) Primer pump WARNING 5 Operation 1. 2. 4 Fuel RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 (when using ZENOAH genuine oil) 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4. Pour In the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. ¦ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 1. Select bare ground for fueling. 2. Move at least 10feet (3meters) away from the fueling point before starting the engine. 3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container. FOR YOUR ENGINE LIFE, AVOID; 1. FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication. 3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking. 4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly. 5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel. 6. In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site. As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to fhe mixed gasoline, etc. described therein, if may not be covered by the warranty. NOTE WARNING Spacer BC2311LE/BC2611 only Guard skirt for line head only [BC2611WE] [BC3501WE/BC4501WE] WARNING [BC3501LE/WE/BC4501WE] • Using at...

Baixe o seu

Para fazer o download, introduza 2 dígitos :