Assessments - 2, GPA: 5 ( )

Fabricante : Bolens Arquivo Tamanho: 2.36 mb Arquivo Nome : Língua de Ensino:

2 Bolt-hex hd„ 3/8-16x2"............. 4 Locknut-3/8"-16.......................... 4 This Ref. No. not used................. This Ref. No. not used................. Bolo Tine-single, left hand. Used on left and right side tine assy. Tine is stamped either “EL" or “AL". (Incl. two each of Ref. No.’s 8, 9 and 10)............................. 8 Bolo Tine-single, right hand. Used on left and right side tine assy. Tine is stamped either “ER" or “AR”. (Incl. same hardware as Ref. No. 6)............................... 8 Bolt-hex hd„ 3/8-16x1"............. 16 Lockwasher-3/8"......................... 16 Nut-hex, 3/8"-16......................... 16 Tine Replacement Kit-unassembled (Incl. eight each of Ref. No.’s 6, and 7, sixteen each of Ref. No.'s 8, 9 and 10). Includes easy-to-follow installation instruction. DOES NOT INCLUDE tine holders, holder mounting hardware, or tine shaft keys................................. 1 1270-2A 8 9711 9 9913 10 9802 ... 1901 REF No. PART No. DESCRIPTION QTY. CUSTOM TILLING TINES Special hard-faced, high-chrome carbon alloy tines that are thicker than standard Bolo Tines. These tines better resist the abrasive action of rocky, gritty or sandy soil as compared to standard Bolo Tines, and are especially suited for custom tilling or market gardening. 10802 Custom Tilling Tine Kit—(Incl. eight each of Part #2475-1 and #2475-2 tines and sixteen each of #9711 bolts and #9807 locknuts........................ 1 2475-1 Bolo Tine, Custom Tilling—single, left hand................................... 8 2475-2 Bolo Tine, Custom Tilling—single, right hand................................ 8 9807 Locknut-hex, 3/8", used in place of Ref. No.’s 9 and 10 when using Custom Tilling Tines....... 16 15 TROY-BILT® HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 FORWARD INTERLOCK SYSTEM (Figure 8) See Figure 1 BRIGGS & STRATTON 8 HP KOHLER 16 MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF PART No. No. DESCRIPTION QTY. 1 2552 Engine Wire Harness Assy-forward interlock system (Incl. one red and one black wire, plug connector, neutral switch and PVC tubing. Parts not available separately................................. 1 2 9971 Lockwasher-external tooth, 7/16"......1 3 9851 Nut-hex, 7/16"-20....................... 1 REF No. PART No. DESCRIPTION QTY. 4 ET69-12 Grommet-for Kohler engine................1 5 ET42-447 Screw-#8 Phillips Head, for Kohler engine............................................................................1 6 9205 Clip-for plug connector..............................1 7 9202 Tie-plastic......................................................................1 8 2551 Handlebar Wire Harness Assy- (see page 2, Ref. No. 20)..................1 Note: Ref. No. 4 may also be obtained at a Tecumseh Engine Authorized Service Center by ordering part no. 69-12. Ref. No. 5 may also be obtained at a Tecumseh Engine Authorized Service Center by ordering part no. 42-326. 17 TROY-BILT® HORSE TILLER MODELS 12068, 12069, 12070 AND 12071 ELECTRIC START SYSTEM - 7HP & 8HP TILLERS (Figure 9) (+) Positive Battery Cable Starter- Solenoid i Ë Activate Wire (Red) ,r°^e TO Engine Base (KoMeT^'99* 18 MODELS 12068, 12069, 12070 AND 12071 TROY-BILT® HORSE TILLER REF PART REF PART No. No. DESCRIPTION QTY. No. No. DESCRIPTION QTY 1 96515 Cable-battery, positive and negative 22 This Ref. No. not used................. terminals.................................. 2 23 9265 Tie-plastic, wire retaining............ 1 2 97020 Boot-terminal insulating............. 3 24 9009 Vent Tube-5/16” diameter........... 1 3 9552 Screw-self-threading, 25 1475 Shield-venttube, 1/2" diameter... 1 1/4-20x1/2“............................ 3 26 9224 Clamp-venttube shield............... 1 4 9780 Bolt-hex hd„ 1/4-20x5/8".......... 2 27 9202 Tie-plastic................................... 2 5 1554 Wire-recharge (red) for Briggs 28 1908118 Wire Harness & Connecting and Stratton engine (inci. Terminal Assy-for Briggs & Stratton terminal and eyelet)................. 1 engines(available as 6 2616 Battery Hold-down Ciamp-with attached Key Switch Plate (incl. Ref. No. 7)............................... 1 complete assembly only). Incl. wire assy., w/connectorto large solenoid stud (red wire); wire 7 1900944 Decal-ignition switch instruc....... 1 assy, w/connector to small 8 1908112 Key Switch-includes two ignition keys (Ref. No. 9), one lockwasher, and one mounting solenoid stud (red wire); wire assy, w/connectorto solenoid grounding screw (red wire); wire nut (lock-washer and nut not assy w/connector to engine ground available separately)................. 1 shut-off (green wire); plastic 9 96520 Key-ignition, one pair.................. 1 protector tube; wire harness; 10 9566 Bolt-carriage, 1/4-20 x 1-1/4"..... 2 connector; wire terminal.......... 1 11 9910 Lockwasher-spring lock, 1/4"...... 2 29 190...

Baixe o seu

Para fazer o download, introduza 2 dígitos :