Assessments - 2, GPA: 4 ( )

Fabricante : Tanaka Arquivo Tamanho: 710.11 kb Arquivo Nome : Língua de Ensino:

Installation of handle (Fig. 1-2) WARNING! When you use steel/rigid blades on straight shaft trimmers or brush cutters, always use barrier bar (2) and shoulder harness with the loop handle. (Fig. 1 -2) Attach the handle to the drive shaft tube with the angle towards the engine. Adjust the location to the most comfortable position before operation. Remove the handle bracket (1) from the assembly. (Fig. 1 -3) Place the handles and attach the handle bracket with four bolts lightly. Adjust to appropriate position. Then fix it firmly with the bolts. Put stop cords (3) and throttle wire (1) through protective tube (2), then unhook the hip pad. (Fig. 1-3B) 5 custsvc@tanaka-ism.com Owner’s ManualTBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Throttle wire/stop cord Remove the air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1 -5) Cover throttle wire and stop cords together with protective tube provided up to air cleaner cover. (Fig. 1 -7) Connect throttle wire end to carburetor. (Fig. 1 -6) TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Throttle wire/stop cord Remove the air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1 -5) Cover throttle wire and stop cords together with protective tube provided up to air cleaner cover. (Fig. 1 -7) Connect throttle wire end to carburetor. (Fig. 1 -6) Installation of blade guard (Fig. 1-8, 8B) Install the blade guard on the drive shaft tube against the gear case. Tighten the guard bracket firmly so that the blade guard does not swing or move down during operation. When using a trimmer head (2), locate the guard above the gear case. (Fig. 1-8C, 8D,8E) CAUTION! Some blade guards are equipped with sharp line limiters. Be careful when handling it. 6 custsvc@tanaka-ism.com Owner’s ManualTBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D When using a trimmer head (Fig.1-9B) with two-piece type blade guard, attachthe guard extension to the blade guard. (Fig. 1-9) Then locate the guard above the angle transmission. (Fig. 1-9B) NOTE! If your unit has guard location label on drive shaft tube, follow the indication. NOTE! To remove the guard extension, refer to the drawings. Wear gloves as the extension has a sharp line limiter, then push the four square tabs on the guard one by one in order. (Fig. 1 -9C) 7 custsvc@tanaka-ism.com Owner’s ManualTBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Installation of cutting blade (Fig. 1-10, 10B) (If so equipped) When installing a cutting blade, make sure the blade is not cracked or damage and the cutting edges are facing the correct direction. NOTE! When installing cutter holder cap (1), be sure to set the concave side toward the blade. Insert the allen wrench (2) into the hole of the gear case in order to lock the cutter holder (3). Please note that the cutter fixing bolt or nut (4) has left handed threads ' (clockwise to loosen/counter-clockwise to tighten). Tighten the fixing bolt or nutwith the box wrench. NOTE! If your unit is of a nut-securing type, the blade must be retained with a new cotter pin (5) each time installed. (Fig. 1 -10C) CAUTION! Before operation, make sure the blade has been properly installed. CAUTION! If your unit is equipped with protection cover under a cutting blade, check it for wear or cracks before operation. If anydamage or wear is found, replace it. Installation of the cutting head NOTE! For installation see your Cutting Head Owner's Manual, provided with the unit. WARNING! For TANAKA heads, use only flexible, non-metallic line recommended by the manufacturer. Never use wire or wire-ropes. They can break off and become a dangerous projectile. NOTE! When using TANAKA alloy head (CH-100), initial cutting line length should be about 17cm (6-3/4”) each. (Fig. 1 -11) 8 custsvc@tanaka-ism.com Owner’s ManualTBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D 4. Operating procedures Fuel (Fig. 2-1) WARNING! The trimmer is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. • Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 25-50:1 (Gasoline (A) : Oil (B)), only for the state of California at 50:1. • Never use multi-grade oil (10 W/30) or waste oil. • Always mix fuel and oil in a separate clean...

Baixe o seu

Para fazer o download, introduza 2 dígitos :