Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
1. Loosen the coupler by turning the knob counterclockwise. CouplerLOOSENTIGHTEN Knob NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1. diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1. diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8. upper shaft. LOWER SHOULDER STRAP CLAMP Spacer Tabs SpacerTabspositionedforuseon1.diameteruppershaft 1. Place the upper shoulder strap clamp over the upper shaft above the handlebar. 2. Remove the shaft cap from the pruner attachment (if present). 3. Position locking/release button of attachment into guide recess of coupler. 4. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 5. Before using the unit, tighten the knob securely by turning clockwise. Coupler Primary Hole Locking/ GuideRecessUpper Lower Release Shaft Attachment Button 2. Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes (use spacer tabs between upper and lower clamps if necessary to secure clamp, i.e. for 1. diameter upper shaft). UpperShoulderStrapClampLowerShoulderStrapClampPOWERHEADENDATTACHMENTEND Screws WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. SHOULDER STRAP ASSEMBLY WARNING: Proper shoulder strap and handle adjustments are required before use. The shoulder strap clamp must be installed as shown above the assist handle on the upper shaft (powerhead end of unit). 3. Insert two screws into the screw holes. 4. Secure shoulder strap clamp by tightening screws with the hex wrench. 5. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. 6. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist. NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoulder. 6 AssistHandle 7. Adjust the strap, allowing the hook to be ADJUSTING THE ASSIST HANDLE about 3 - --6 inches below the waist. 8. Fasten the strap hook to the upper clamp WARNING: When adjusting the as- and lift the tool to the operating position. sist handle, be sure it remains directly above the coupler on the engine end shaft to ensure proper balancing of unit. Coupler ShoulderStrapShoulderStrapClamp OPERATION KNOW YOUR PRUNER ATTACHMENT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR PRUNER ATTACHMENT. Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. ShaftCouplerPrunerChainBarBarnut Hanger Bar oil fill cap PRUNER CHAIN TENSION The PRUNER is designed for removal of It is normal for a new chain to stretch during limbs and branches overhead not greater first 15 minutes of operation. You should than 4 inches in diameter. check your chain tension frequently. See CHAIN TENSION in the SERVICE AND ADJUSTMENTS section. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: MODEL: Edger ....................... PP1000E Cultivator .................... PP2000T Blower ...................... PP3000B Brushcutter .................. PP4000C WARNING: Always disconnect powerhead spark plug (or disconnect powerhead from power source) before removing or installing attachments. 7 REMOVING PRUNER ATTACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION: When removing or installing at tachments, place the powerhead and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Upper Shaft LOOSEN TIGHTEN Knob Coupler S Never use waste oil for bar and chain lubrication. S Always stop the engine before removing the oil cap. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. LowerAttachmentLocking/ReleaseButtonCouplerUpperShaftLowerAttachment 2. Press and hold the locking/release button. 3. Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. ...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 530163467 (176.43 kb)