Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
• Always evaluate the branches to be pruned for hazards such as loose dead branches which may fall and strike the operator or helpers. Remove hazards before pruning. • Plan retreat path from falling objects. • Cut branches bounce when striking ground. • Check that shoulder harness is adjusted for safe, comfortable operation. See picture at right for proper adjustment. • Turn the Power PrunerTM off when moving from tree to tree. • Avoid any contact with saw chain. Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. kIckback WARNING Kickback can lead to dangerous loss of control of the Power PrunerTM and result in serious injury to the operator orany one standing close by. Hold the Power PrunerTM firmly with both hands with thumbs and fingers encircling thefront and rear handles. Be aware of the down and outward path the pruner will take after the cut is made. Kickback may occur when the moving saw chain at the nose or tip ofthe guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. In some cases this may cause a lightning-fastreverse action, kicking the guide bar and saw chain up and back ordown and back towards the operator. Either of these reactions may cause the operator to lose control of the Power PrunerTM which could result in serious personal injury. With a basic understanding of kickback, you can reduce or eliminate the element of surprise which contributes to accidents. Avoid contact of the guide bar tip with any object while the saw chain is moving. Cut only wood. Avoid striking concrete, metal, wire, or other obstructions which could cause kickback or damage to the saw chain. If the saw chain does strike a foreign object, immediately stop the engine, inspect and repair the Power PrunerTM if necessary. equIpment WARNING Serious injury may result from the use of non approved guide bar and saw chain combinations. ECHO, INC. will notbe responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHOfor use with this unit. Read and comply with all safety instructions listed in this manual. • Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed. Guide Bar and Saw Chain • Check that the cutting attachment, guide bar, and saw chain is firmly attached and in safe operating condition. • Use only one Echo-approved extension on the pruner. • Do not hit rocks, stones, tree stumps, and other foreign objects with the saw chain. • Do not cut into the ground with the saw chain. • If cutting attachment end strikes an obstruction, stop engine immediately and inspect saw chain for damage. • Do not operate with a dull, fractured, or discolored saw chain. • Remove all foreign objects from work area. • Always cover the guide bar and saw chain with guide bar cover during transportation and for storage. WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. • ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stopbefore removing obstructions, clearing debris, or servicing unit. • DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. • NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings. WARNING Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho- rized servicing dealer before using. emIssIon control (eXhaust & evaporatIve)& evaporatIve) EPA 2010 and Later and/or C.A.R.B. TIER III The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to California models only. An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY). PRODUCT EMISSION DURAbILITy (EMISSION COMPLIANCE PERIOD) The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. P/N X505002310 Hot Decal (near muffler) descrIptIonLocate this safety decal on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. 22 14 13 15 1617 18 20 19 21 Power PrunerTMOperator's Manual9 112 11 10 2 9 8 7 6 5 4 PPT-265 PPT-265H 112 11 10 9 87 6 5 4 2 9 112 11 10 2 9 8 7 6 5 4 P...
Este manual também é adequado para os modelos :Ferramentas para Jardim - PPT-265S (1.22 mb)