Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
See chapter on Technical data. • Fit the drive disc (B) on the angle gear’s output shaft. • Centre the metal cup (P) on the drive disc’s blade guide. • Turn the output shaft until one of the holes in the drive disk aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Position the blade (D) with the drive disk (B). Make sure that the blade is centered by fitting it to the guide on the drive disk. • Fit the support flange (F) on the output shaft so that it rests against the blade. E N F D B C A M L P • Screw the support cup (E) onto the output shaft threads (CAUTION! Left-hand thread). Tighten to a torque of 3550 Nm (3.5-5.0 kpm). Use the socket spanner in the tool kit. Note that the locking pin (C) must remain inside the gear housing to lock the drive disk. Hold the shaft of the socket spanner as close to the blade guard/combination guard as possible. ! WARNING! Tighten the lock screw (N) in the center hole of the support cup. Tighten to a torque of 35-50 Nm (3.5-5.0 kpm), CAUTION! Left-hand thread. If the lock screw is not fitted in the support cup, there is a risk that the support cup will come unscrewed.This means that the blade will also come loose, which could result in serious or fatal injury to the operator or others. Fitting the blade guard and saw blade • The blade guard (A) is fitted using 4 screws (L) as shown. A L CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. • Fit the drive disc (B) on the output shaft. 14 – English ASSEMBLY • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Place the blade (D) and support flange (F) on the output shaft. FG D B C • Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread). When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade.You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut. Fitting the trimmer guard and trimmer head Trimmy SII • Fit the correct trimmer guard (A) for use with the trimmer head. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram. • Fit the drive disc (B) on the output shaft. • Centre the metal cup (P) on the drive disc’s blade guide. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Screw on the trimmer head (H) in the opposite direction to the direction of rotation. B A M L H P L A M C H C • Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm). • To dismantle, follow the instructions in the reverse order. Fitting other guards and cutting attachments Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram. B A M L H P • Fit the drive disc (B) on the output shaft. • Centre the metal cup (P) on the drive disc’s blade guide. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. L A M C • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. • To dismantle, follow the instructions in the reverse order. English – 15 ASSEMBLY Adjusting the harness and clearing saw ! WARNING! When using a clearing saw it must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release. Standard harness Safety release At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness. Spreading the load on your shoulders A well-adjust...
Este manual também é adequado para os modelos :Ferramentas para Jardim - BC2145 (2.08 mb)