Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Turn the control sideways and insert the lever up through the wide portion of the slot on the handle panel. See figure 8A. After the end of the lever is through the slot, turn and then tip the control forward as shown in figure -8B to slide it through the slot. NOTE The lever must be all the way to the back of the control housing as shown in figure 8B. Push the control back into the slot in the handle panel and press in place. Be certain the control is locked securely into the slot. 4. Secure the throttle control to the handle panel using the self-tapping screw (X). See figure 8D. ATTACHING THE TINE CLUTCH CONTROL CABLE The clutch control cables are already attached to the unit. The tine clutch control cable has a “Z” fitting on the loose end. This cable attaches to the left handle. ■I^NOTE Both the drive clutch cables and the tine clutch cable are attached to springs, which are hooked to bolts. If either the cable or spring has come loose in shipping, it must be reassembled. Refer to page 18, reference numbers 2, 5, 11, 12, 15, 17 and 21. Remove one nut and the lock washer from the end of the tine clutch cable (short cable). Slip the cable up through the slot on the cable bracket on the left handle. Rethread hex nut and lock washer on the ■end of the cable. See figure 9. Do not tighten at this time. 1. 6 I Hole in FIGURE 10. 2. Hook the “Z” end of tine clutch cable into the hole in tine clutch lever. 3. With the clutch lever released (in the “up” position), adjust the bottom nut at the cable bracket so there is only a slight amount of slack in the control wire. Tighten the upper nut against the bracket. Squeeze the clutch lever against the handle. The —control wire should now be straight. See figure 10. NOTE Do not overtighten control wire. Too much tension may cause it to break. ATTACHING THE DRIVE CONTROL CABLES 1. The drive clutch cables are already attached to the unit. Attach the other end of cables to the upper hole of drive clutch lever (W), one on each side, using hex bolt (R) and hex lock nut (S). See figure 11. 2. Remove one nut and the lock washer from the end of each drive clutch cable. Thread the other hex nut all the way down the cable as far as it will go as shown in figure 11. FIGURE 11. Gripped End of Clutch Lever Slots on Cable Bracket 3. 4. 5. Push the gripped end of drive clutch lever through the slot in the handle panel. Slip the wire on the cables through the slots in the cable brackets as shown in figure 12. Push the ends of the cable up through the holes in the bracket. Rethread hex nuts and lock washers on the end of the cables. Do tighten at this time. Place end of drive clutch lever over weld bolt on handle panel. See figure 12. FIGURE 12. 7 I FIGURE 13. 6. Secure drive clutch lever to weld bolt with rubber washer (T), flat washer (U) and hex lock nut (V). — See figure 13. Tighten hex nut. 7. Place the drive clutch lever in the neutral (N) position. Adjust the cables at the cable bracket so that the cables are tight, then tighten the hex nuts against the cable bracket. IMPORTANT Service engine with oil and gasoline before checking the drive clutch adjustment. Refer to the separate engine manual packed with your tiller. 8. Check the adjustment of the drive clutch as follows. Place the unit against a solid object (wall, fence, etc.). With the tine clutch lever released and the drive clutch lever in the neutral position, carefully start the engine. If the unit shows any signs of motion with the drive clutch lever in neutral, shut the engine off immediately and readjust the hex nuts at the cable bracket. Recheck the adjustment as necessary. 9. Secure the cables to the handles as with cable ties (L). Cut off excess ends of cable ties. CONTROLS —Location and Use Throttle Control The throttle control lever is located on the righl hand side of handle panel and controls the engine speed. See figure 14. 1. Start—Push throttle control lever forward (down) to start position. 2. Stop—Pull lever back (upward) to stop the e igine. Tine Clutch Lever The tine clutch lever is located on the left handle. See figure 14. Squeeze the lever down to engage the tines. Release the lever to disengage the tines. Drive Clutch Lever The drive clutch lever is located on the left hand side of handle panel. See figure 14. The drive clutch lever may be placed in one of three positions. 1. Forward (F)—Move the drive clutch lever to the left and all the way forward to engage the drive mechanism to the wheels. 2. Neutral (N)—Move lever to the detent marked “N”. Be certain lever is in neutral position when starting the engine. 3. Reverse (R)—Raise up on the handles to lift the tines out of the ground and pull the drive clutch lever back (upward) slowly to obtain reverse. Always use caution when using the reverse. When using reverse, if gear shift lever is released it will snap back into neutral (N). 8 OPERATION ■^NOTE Engine is shipped without oil. BEF...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 216-403-000 (2.56 mb)