Assessments - 0, GPA: 4
(
)
)
|
Facilidade de uso
Attachment CouplerKnobLOOSEN TIGHTEN 2. Press and hold the locking/release button. Locking/Release Button Attachment Upper Shaft Coupler 3. While securely holding the engine and upper shaft, pull the attachment straight out of the coupler. INSTALLING OPTIONAL ATTACHMENTS 1. Remove the shaft cap from the attachment (if present). 2. Position locking/release button of attachment into guide recess of coupler. 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. Primary Hole Coupler Guide Recess Locking/ Upper Attachment Release Shaft Button WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit. Locking/ReleaseButtoninPrimaryHole OPERATING POSITION ALWAYSWEAR: Safety helmet Hearing protection Eye protection Heavy, long pants Boots Cut from your left to your right. When operating unit, clip shoulder strap onto clamp, stand as shown and check for the following: 10 S Wear eye protection and heavy clothing. S Extend your left arm and hold loop handle with your left hand. S Hold throttle grip with your right hand with finger on throttle trigger. S Keep unit below waist level. S Keep shoulder strap pad centered on your left shoulder. S Maintain full weight of tool on your left shoulder. S Without bending over, keep the blade or trimmer head near and parallel to the ground and not crowded into material being cut. OPERATING INSTRUCTIONS FOR USE WITH TRIMMER HEAD WARNING: Always wear eye protection. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. Before trimming, bring engine to a speed sufficient to cut material to be trimmed. Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool. Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine: S Release the throttle trigger. S Push and hold the ON/STOP switch in the STOP position until the engine stops. TRIMMER LINE ADVANCE Advance line by tapping the bottom of the cutting head lightly on the ground while engine is running at full speed. The metal line limiter blade attached to the guard will cut the line to the proper length. WARNING: Use only 2,4 mm diameter line. Other sizes of line will not advance properly and will result in improper cutting head function or can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury. CUTTING METHODS WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard. S The tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below. Tip of line does Line crowded into the cutting. work area. RightWrong S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. S For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially: S During light duty cutting. S Near objects around which the line can wrap such as small posts, trees or fence wire. S For mowing or sweeping, use full throttle for a good clean job. TRIMMING - --Hold the bottom of the trimmer head about 8 cm above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area. Trimming8cmaboveground SCALPING - --The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 8 cm above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. Scalping MOWING- --Yourtrimmerisidealformowinginplacesconventionallawnmowerscannotreach.Inthemowingposition,keepthelineparalleltotheground.Avoidpressingtheheadintothegroundasthiscanscalpthegroundanddamagethetool. 11 MowingMowing SWEEPING- --Thefanningactionoftherotatinglinecanbeusedtoblowawayloosedebrisfromanarea. Keepthelineparalleltoandabovetheareasurfaceandswingthetoolfromsidetoside. Sweeping OPERATING INSTRUCTIONS FOR USE WIT...